Saturation Properties Sensor (2P)
Libraries:
Simscape /
Foundation Library /
Two-Phase Fluid /
Sensors
Description
The Saturation Properties Sensor (2P) block represents an ideal sensor that lets you measure these liquid and vapor saturation properties in a two-phase fluid network:
Saturated temperature, specific volume, internal energy, or enthalpy, based on the pressure measurement
Saturated pressure based on the temperature measurement
The block measures these properties at the node connected to port A. There is no mass or energy flow through the sensor.
By default, only the output ports that measure the saturated liquid and vapor temperatures, TL and TV, are visible on the block icon. Use the block parameters to control visibility of output ports for the other measurements.
Ports
Output
TL — Saturated liquid temperature, K
physical signal
Physical signal output port that measures the saturated liquid temperature based on the pressure at port A.
Dependencies
To enable this port, select the Saturated temperature measurement check box.
TV — Saturated vapor temperature, K
physical signal
Physical signal output port that measures the saturated vapor temperature based on the pressure at port A.
Dependencies
To enable this port, select the Saturated temperature measurement check box.
PL — Saturated liquid pressure, MPa
physical signal
Physical signal output port that measures the saturated liquid pressure based on the temperature at port A.
Dependencies
To enable this port, select the Saturated pressure measurement check box.
PV — Saturated vapor pressure, MPa
physical signal
Physical signal output port that measures the saturated vapor pressure based on the temperature at port A.
Dependencies
To enable this port, select the Saturated pressure measurement check box.
UL — Saturated liquid specific internal energy, kJ/kg
physical signal
Physical signal output port that measures the saturated liquid specific internal energy based on the pressure at port A.
Dependencies
To enable this port, set the Energy measurement parameter
to Saturated specific internal energy
.
UV — Saturated vapor specific internal energy, kJ/kg
physical signal
Physical signal output port that measures the saturated vapor specific internal energy based on the pressure at port A.
Dependencies
To enable this port, set the Energy measurement parameter
to Saturated specific internal energy
.
HL — Saturated liquid specific enthalpy, kJ/kg
physical signal
Physical signal output port that measures the saturated liquid specific enthalpy based on the pressure at port A.
Dependencies
To enable this port, set the Energy measurement parameter
to Saturated specific enthalpy
.
HV — Saturated vapor specific enthalpy, kJ/kg
physical signal
Physical signal output port that measures the saturated vapor specific enthalpy based on the pressure at port A.
Dependencies
To enable this port, set the Energy measurement parameter
to Saturated specific enthalpy
.
VL — Saturated liquid specific volume, m^3/kg
physical signal
Physical signal output port that measures the saturated liquid specific volume based on the pressure at port A.
Dependencies
To enable this port, set the Density measurement parameter
to Saturated specific volume
.
VV — Saturated vapor specific volume, m^3/kg
physical signal
Physical signal output port that measures the saturated vapor specific volume based on the pressure at port A.
Dependencies
To enable this port, set the Density measurement parameter
to Saturated specific volume
.
rhoL — Saturated liquid density, kg/m^3
physical signal
Physical signal output port that measures the saturated liquid density based on the pressure at port A.
Dependencies
To enable this port, set the Density measurement parameter
to Saturated density
.
rhoV — Saturated vapor density, kg/m^3
physical signal
Physical signal output port that measures the saturated vapor density based on the pressure at port A.
Dependencies
To enable this port, set the Density measurement parameter
to Saturated density
.
Conserving
A — Sensor inlet
two-phase fluid
Two-phase fluid conserving port associated with the sensor inlet. Connect this port to the node in the two-phase fluid network for which you want to measure liquid and vapor saturation properties.
Parameters
Saturated temperature measurement — Measure saturated liquid and vapor temperature based on pressure
On
(default) | Off
Selecting this check box exposes output ports TL and TV, which measure the saturated liquid and vapor temperature, respectively, based on the pressure at port A.
Saturated pressure measurement — Measure saturated liquid and vapor pressure based on temperature
Off
(default) | On
Selecting this check box enables the Saturated pressure beyond min and max pressure parameter and exposes output ports PL and PV, which measure the saturated liquid and vapor pressure, respectively, based on the temperature at port A.
Saturated pressure beyond min and max pressure — Reporting preference for out-of-bounds saturated pressure
Error
(default) | Warning
| None
When either of the saturated pressures is below the minimum pressure or above the maximum pressure specified in the fluid properties, then the saturated pressure value is based on extrapolated values of the temperature tables, rather than the interpolation within the table. Choose your reporting preference for when the saturated pressure is out of bounds:
Error
— Simulation stops with an error.Warn
— The block issues a warning.None
— The block does not issue an assertion.
Dependencies
To enable this parameter, set Saturated pressure measurement
to On
.
Energy measurement — Measure saturated specific internal energy or saturated specific enthalpy based on pressure
Off
(default) | Saturated specific internal energy
| Saturated specific enthalpy
Setting this parameter to:
Saturated specific internal energy
— Exposes output ports UL and UV, which measure the saturated specific internal energy of liquid and vapor, respectively, based on the pressure at port A.Saturated specific enthalpy
— Exposes output ports HL and HV, which measure the saturated specific enthalpy of liquid and vapor, respectively, based on the pressure at port A.
Density measurement — Measure saturated specific volume or saturated density based on pressure
Off
(default) | Saturated specific volume
| Saturated density
Setting this parameter to:
Saturated specific volume
— Exposes output ports VL and VV, which measure the saturated specific volume of liquid and vapor, respectively, based on the pressure at port A.Saturated density
— Exposes output ports rhoL and rhoV, which measure the saturated density of liquid and vapor, respectively, based on the pressure at port A.
Extended Capabilities
C/C++ Code Generation
Generate C and C++ code using Simulink® Coder™.
Version History
Introduced in R2021aR2023a: Usability enhancement for sensors
The Saturation Properties Sensor (2P) block now has the Saturated temperature measurement check box, which controls the visibility of ports TL and TV on the block icon. The Saturated pressure measurement parameter, which controls the visibility of ports PL and PV, is now a check box.
This change has no compatibility impact.
See Also
Commande MATLAB
Vous avez cliqué sur un lien qui correspond à cette commande MATLAB :
Pour exécuter la commande, saisissez-la dans la fenêtre de commande de MATLAB. Les navigateurs web ne supportent pas les commandes MATLAB.
Select a Web Site
Choose a web site to get translated content where available and see local events and offers. Based on your location, we recommend that you select: .
You can also select a web site from the following list:
How to Get Best Site Performance
Select the China site (in Chinese or English) for best site performance. Other MathWorks country sites are not optimized for visits from your location.
Americas
- América Latina (Español)
- Canada (English)
- United States (English)
Europe
- Belgium (English)
- Denmark (English)
- Deutschland (Deutsch)
- España (Español)
- Finland (English)
- France (Français)
- Ireland (English)
- Italia (Italiano)
- Luxembourg (English)
- Netherlands (English)
- Norway (English)
- Österreich (Deutsch)
- Portugal (English)
- Sweden (English)
- Switzerland
- United Kingdom (English)