Getting Started with Sphero Connectivity Package

This example shows how the Sphero Connectivity Package can be used to connect to a Sphero device and perform basic operations on the hardware, such as change the LED color, calibrate the orientation of the robot and move it in a particular direction.


Open this example


The Sphero Connectivity Package enables us to communicate with a Sphero device remotely from a computer running MATLAB®. The package includes command line interface to control the robotic ball.

In this example we will learn how to create a sphero object to connect to the Sphero device from within MATLAB®. We will examine the properties and methods of this object to control the robot and its peripherals.

Required Hardware

To run this example, the following hardware is required:

Setup hardware

In order to connect to the Sphero, first make sure that the Sphero is awake and ready for connection. The steps to set up the Sphero for connection can also be found in the readme.txt file as well as in the Quick Start Guide that comes with the Sphero.

Note that in general the following steps need to be done only the first time when you unpack the sphero and then once in a while (specifically steps 1 to 3) when the battery is low and needs to be recharged.

  1. Connect the Charger to a wall socket
  2. Place the Sphero in the charger with its heavy part at the bottom.
  3. Remove the Sphero from the charger after it lights up after a few seconds. It will be asleep at after it is taken out from the charger
  4. Double tap (ver 2.0) or shake (ver 1.0) the Sphero with your fingers to wake it up
  5. The Sphero blinks 3 unique colors until it is connected to another device. Sphero's Bluetooth name will contain the initials of the 3 unique colors it is blinking with. The Sphero's Bluetooth name could be useful later in case you have several Spero devices and want to connect to a specific one.
    R = RED
    B = BLUE
    G = GREEN
    Y = YELLOW
    O = ORANGE
    P = PURPLE
    W = WHITE
  6. Pair the Sphero device with your phone, and launch the Sphero app. This would automatically update the firmware on the device
  7. Disconnect the Sphero device from your phone by closing the Sphero app. Then access the phone Bluetooth settings, select the sphero among the Bluetooth devices, and select "forget this device". This prevents the sphero from automatically pairing up with the phone later.
  8. Turn on Bluetooth on your computer, and pair the Sphero to it, following the instructions mentioned in one of the following web pages. If a prompt shows up to compare the pairing codes between your computer and the Bluetooth device, click on 'Yes' to 'Accept' the pairing code.
    Windows 7
    Mac (Please note that Bluetooth interface is supported only for Mac OS 10.7 and earlier)

Creating a sphero object (if it does not already exist)

Once the sphero is charged and paired with the computer, and the package is installed, then as soon as the sphero is woken up (which can be done by either shaking it (ver 1.0) or double tapping it (ver 2.0), it can be directly accessed from MATLAB® as shown below:

if ~exist('sph','var'),
    sph = sphero(); % Create a Sphero object
    created=1;      % this is so we remember to delete it later

% make sure the object is connected

The sph is a handle to a sphero object. While creating the sph object, MATLAB® searches for the paired sphero devices and prompts the user to select one for connection. It then opens the Bluetooth connection with the Sphero.

If you face any issues creating the sphero object, please refer to the Troubleshooting Connection Issues with Sphero page.

The properties of the sphero object show information such as the status of the connection and Bluetooth name of the connected device. It also has properties that can be used to modify the color of the LED on the Sphero, the brightness of the back LED, timeouts for motion, response and inactivity among other things.

Perform simple operations on Sphero

The various methods of the sphero object can be used to perform different operations. The status of the Bluetooth connection can be checked by using the 'Status' property of the object:

s = sph.Status
s =


We can also check whether the Sphero is able to receive and respond to messages by using the following command:

result = ping(sph);

% interrupt the example if ping was not successful
if ~result,
    disp('Example aborted due to unsuccessful ping');

If you receive an error when running these commands, please refer to the Troubleshooting Connection Issues with Sphero page.

The color of the LED on the Sphero, and the brightness of the back LED can be changed by using the appropriate properties of the object

sph.Color = 'r'; % Change color of LED to red
sph.BackLEDBrightness = 255; %255 sets it to maximum brightness

The back LED of the Sphero indicates the back of the Sphero. We will learn more about this in the Move Sphero section.

sph.Color = [127 127 127]; % A custom color can also be provided for the LED by specifying RGB values

Move Sphero

The sphero object provides basic commands for moving the Sphero. But before we start moving it, we need to make sure that the Sphero is oriented in the correct direction.

The calibrate method can be used to calibrate the orientation of the Sphero. As mentioned in the Perform simple operations on Sphero section, the back LED indicates the back of the robot. Thus the y-axis, 0 angle or the front of the robot is indicated by the direction opposite to the back LED.

Thus we would need to calibrate the orientation of the robot so that its back is oriented towards you. The calibrate command might have to be used multiple times in order to fine tune and calibrate the robot's orientation

sph.BackLEDBrightness = 255; % turn on the back LED before we start calibrating the orientation of the robot


calibrate(sph, 60); % Observe that the sphero is going to rotate by 60 degrees and reset its orientation.
% Run this command again with a different value for the angle if the back
% of the robot is not oriented towards you at present.

Once the robot is orientated properly, we can move it along a particular direction. Please note that all the 'angle' values that the following commands use are the angles from the original calibrated orientation of the robot

speed = 70;
angle = 0;


roll(sph, speed, angle);

pause(0.5); % Wait for half a seconds and then brake the Sphero
%Turn it by 180 degrees
roll(sph, speed, 180);

pause(0.5); % Wait for half a seconds and then brake the Sphero

For all the aforementioned commands, we can turn on handshaking to make sure that the sphero is receiving and responding to the commands that are being sent to it

sph.Handshake = 1;

You will notice that the Sphero rolls in the particular direction for a small amount of time and then it stops automatically. This is due to the MotionTimeout property of the object. The robot keeps moving until the time in seconds that is specified by this property

sph.MotionTimeout = 3; % Set the timeout for motion to 3 seconds
roll(sph, speed, angle);

pause(1); % Wait for 1 second and then brake the Sphero

There are other move commands such as boost or rawMotor which can be used to move the sphero with high speed and provide raw motor commands to control the speed of the motors respectively

Read Sensor Data

To read the data of a set of sensors from the Sphero, execute the command similar to the following.

disp('Reading Sensor Data');

[accX, accY, distX, distY] = readSensor(sph, {'accelX', 'accelY', 'distX', 'distY'});
Reading Sensor Data

In order to read the value of a set of sensors at a particular rate, and save it to a MAT file, use the following command. By default, the sensor data is saved to log.mat

disp('Logging Sensors');

%Log accelerometer X and Y data at 1Hz, 1 frame per packet, 10 packets
logSensors(sph, 1, 1, 10, 'sensorname', {'accelX', 'accelY'});

% wait 5 seconds to illustrate sensor logging

% interrupt the sensor polling opened by the logSensors function
Logging Sensors

Disconnect or Make the Sphero go to Sleep

We can disconnect from the Sphero by using the disconnect command. It is possible to reconnect to it again by using the connect command. If a different Sphero device name is specified as an input argument to the connect command, it will try to connect to the new device instead of the previous one.

% get the device name
devname = sph.DeviceName;

% disconnect
disp('Disconnecting Sphero');

% wait a couple of seconds before reconnecting

disp('Reconnecting Sphero');
connect(sph, devname); % or, for example: connect(sph,'Sphero-RGR;);

% wait a second before going to sleep
Disconnecting Sphero
Reconnecting Sphero

The sleep command can be used to force the currently connected Sphero to go to sleep

disp('Forcing Sphero to go to sleep');
Forcing Sphero to go to sleep

See Also

Copyright 2015, The MathWorks, Inc.