Publié le
Comparing Runs using Simulation Data Inspector
Do you use the Simulation Data Inspector? Here is an example where it saved me a lot of debugging time. Simulation...
environ 13 ans il y a
Publié le
Zero-Crossing Detection… what are your options?
When using Simulink variable-step solvers, zero-crossing detection is very useful to capture events accurately. However for...
environ 13 ans il y a
Réponse apportée
In a For Iterator Subsystem, how to use the iteration variable ?
The iteration variable is a signal coming out of the For Iterator block. Inside the subsystem, you can use a Selector block:...
In a For Iterator Subsystem, how to use the iteration variable ?
The iteration variable is a signal coming out of the For Iterator block. Inside the subsystem, you can use a Selector block:...
environ 13 ans il y a | 0
Publié le
Implementing a PID Controller on an Arduino Board
This week my colleague Pravallika is back to continue her motor control story! In my previous post, we saw how to estimate...
environ 13 ans il y a
Réponse apportée
Initial condition for Memory block with TRIM (Linear Analysis Tool)
The Memory block has an option "Direct feedthrough of input during linearization" if you do not want to initialize it during lin...
Initial condition for Memory block with TRIM (Linear Analysis Tool)
The Memory block has an option "Direct feedthrough of input during linearization" if you do not want to initialize it during lin...
environ 13 ans il y a | 0
Réponse apportée
Pressure relief valve with proportional control
I recommend using a Pressure Sensor and the Variable Area Orifice. then write a Simscape component (or use blocks from the Physi...
Pressure relief valve with proportional control
I recommend using a Pressure Sensor and the Variable Area Orifice. then write a Simscape component (or use blocks from the Physi...
environ 13 ans il y a | 0
Réponse apportée
linearising a non-linear plant model
It looks like you are in the right direction: - The System Identification Toolbox is the tool to identify the relation betwee...
linearising a non-linear plant model
It looks like you are in the right direction: - The System Identification Toolbox is the tool to identify the relation betwee...
environ 13 ans il y a | 0
| A accepté
Publié le
Creating Driver Blocks for Arduino, Lego, and other targets
As you may know, it is easy to run Simulink models on a set of supported target hardware. This has been possible since...
environ 13 ans il y a
Publié le
To Latch or not to Latch?
Yesterday I explained to a colleague the effect of the Inport block option Latch input for feedback signals of function-call...
environ 13 ans il y a
Réponse apportée
nested Simulink While Iterators
I don't remember using nested iterator subsystem myself. I was curious, so I searched our database and I cannot find reports of ...
nested Simulink While Iterators
I don't remember using nested iterator subsystem myself. I was curious, so I searched our database and I cannot find reports of ...
environ 13 ans il y a | 0
Réponse apportée
Variable Time Step Solver
I confirm: The "tout" signal apply to all signals that have a "continuous sample time. If you want to see more of what the co...
Variable Time Step Solver
I confirm: The "tout" signal apply to all signals that have a "continuous sample time. If you want to see more of what the co...
environ 13 ans il y a | 0
Réponse apportée
Modify dynamically a sample time in Simulink
Sample time cannot change during simulation. What you can do is set the sample time as the smallest possible rate you want to...
Modify dynamically a sample time in Simulink
Sample time cannot change during simulation. What you can do is set the sample time as the smallest possible rate you want to...
environ 13 ans il y a | 1
Réponse apportée
Simscape: Create unidirectional Locking mechanism component
You will not be able to implement a pure lock. Using Simscape language, you could write an ssc-file to "lock" by enabling a stif...
Simscape: Create unidirectional Locking mechanism component
You will not be able to implement a pure lock. Using Simscape language, you could write an ssc-file to "lock" by enabling a stif...
environ 13 ans il y a | 0
Réponse apportée
Difference between 3D Animation Toolbox vs SimMechanics?
If you already implemented the equations in Simulink I would go for Simulink 3D Animation. You will need to find/create VRML obj...
Difference between 3D Animation Toolbox vs SimMechanics?
If you already implemented the equations in Simulink I would go for Simulink 3D Animation. You will need to find/create VRML obj...
environ 13 ans il y a | 2
Réponse apportée
Using same gobal simulation options for a model and all the models that are referred in it
Share the configuration, see details here: http://www.mathworks.com/help/simulink/ug/sharing-a-configuration-set-between-refe...
Using same gobal simulation options for a model and all the models that are referred in it
Share the configuration, see details here: http://www.mathworks.com/help/simulink/ug/sharing-a-configuration-set-between-refe...
environ 13 ans il y a | 0
| A accepté
Publié le
New for R2013a: Time Scope with Triggering!
Today we are happy to welcome guest blogger Kirthi Devleker to talk about a new trigger functionality added to the Time...
environ 13 ans il y a
Réponse apportée
Comment a block or subsystem in simulink
Right-click on it and select "Comment out": http://www.mathworks.com/help/simulink/ug/editing-blocks.html#btms_1l Ctrl+Shi...
Comment a block or subsystem in simulink
Right-click on it and select "Comment out": http://www.mathworks.com/help/simulink/ug/editing-blocks.html#btms_1l Ctrl+Shi...
environ 13 ans il y a | 2
| A accepté
Publié le
Time to Convert to Variant Subsystems
If you are a user of Configurable Subsystems, it is time to start thinking about making the switch to Variant...
environ 13 ans il y a
Réponse apportée
Simulink "While Iterator" subsystem development and debugging
The dataset logging format allows you to log all the iterations of For and While Iterator subsystems http://blogs.mathworks.c...
Simulink "While Iterator" subsystem development and debugging
The dataset logging format allows you to log all the iterations of For and While Iterator subsystems http://blogs.mathworks.c...
environ 13 ans il y a | 0
| A accepté
Réponse apportée
State Space with variable parameters
Do it with basic blocks. A few Product, Sum, and Integrator blocks will do the job. This solution might help: http://www.m...
State Space with variable parameters
Do it with basic blocks. A few Product, Sum, and Integrator blocks will do the job. This solution might help: http://www.m...
environ 13 ans il y a | 0
| A accepté
Réponse apportée
How to group same buses together over a MUX ?
Use Concatenate: http://www.mathworks.com/help/simulink/slref/concatenate.html
How to group same buses together over a MUX ?
Use Concatenate: http://www.mathworks.com/help/simulink/slref/concatenate.html
environ 13 ans il y a | 0
| A accepté
Publié le
Some of My Favorite New Features in R2013a
MATLAB R2013a is now available for download! At the end of this post, I reveal my favorite feature in R2013a… what will it...
environ 13 ans il y a
Réponse apportée
how to integrat matlab simulink model in a raspberry pi????
You have a good timing! It is available today in R2013a: http://www.mathworks.com/academia/raspberry-pi/
how to integrat matlab simulink model in a raspberry pi????
You have a good timing! It is available today in R2013a: http://www.mathworks.com/academia/raspberry-pi/
environ 13 ans il y a | 1
| A accepté
Réponse apportée
HOW TO MAKE ODE14X RUN WITHOUT ERRORS?
Very likely this is because the dynamics in your model is too fast to be captured by the solver step size. You know... the Nyqui...
HOW TO MAKE ODE14X RUN WITHOUT ERRORS?
Very likely this is because the dynamics in your model is too fast to be captured by the solver step size. You know... the Nyqui...
environ 13 ans il y a | 0
Réponse apportée
The art of delaying (discrete)
Sample Time Offset: http://blogs.mathworks.com/seth/2011/11/20/sample-time-offset/
The art of delaying (discrete)
Sample Time Offset: http://blogs.mathworks.com/seth/2011/11/20/sample-time-offset/
environ 13 ans il y a | 1
| A accepté
Réponse apportée
how to write a program or a simulink block of a 3 dimensional nonlinear torsional equations of a mechanical system?
This might help if you want to use SimMechanics: http://www.mathworks.com/tagteam/43892_AIAA20076479KennedyFinal.pdf
how to write a program or a simulink block of a 3 dimensional nonlinear torsional equations of a mechanical system?
This might help if you want to use SimMechanics: http://www.mathworks.com/tagteam/43892_AIAA20076479KennedyFinal.pdf
environ 13 ans il y a | 0
Réponse apportée
Why does my If Action block have vertical bars next to port names?
It is an optional display to let you know if the execution context of the conditionally executed subsystem can propagate outside...
Why does my If Action block have vertical bars next to port names?
It is an optional display to let you know if the execution context of the conditionally executed subsystem can propagate outside...
environ 13 ans il y a | 2
| A accepté
Réponse apportée
Pneumatic Check Valve - how do I model one from basic elements?
You have 2 options: - Build it using basic components. This will very likely involve some mechanical components like spring-m...
Pneumatic Check Valve - how do I model one from basic elements?
You have 2 options: - Build it using basic components. This will very likely involve some mechanical components like spring-m...
environ 13 ans il y a | 1
Réponse apportée
Programmatically Building a Rapid Simulation (RSim) Target
did you try slbuild? http://www.mathworks.com/help/simulink/slref/slbuild.html
Programmatically Building a Rapid Simulation (RSim) Target
did you try slbuild? http://www.mathworks.com/help/simulink/slref/slbuild.html
environ 13 ans il y a | 0
| A accepté
Réponse apportée
Identical blocks in Simulink with identical inputs from different sources results in different solutions
Are the colors in your image sample time colors? If yes, do you have the same response using ode1 solver? If ode1 solver give...
Identical blocks in Simulink with identical inputs from different sources results in different solutions
Are the colors in your image sample time colors? If yes, do you have the same response using ode1 solver? If ode1 solver give...
environ 13 ans il y a | 1