A répondu
Evolving 'Aggregate Equivalent Length of local resistances' within a simulation?
Since you have access to the Simscape code of this block, you may make the 'Aggregate Equivalent Length of local resistances' no...

plus d'un an il y a | 0

A répondu
How can I move a double acting cylinder by force?
I believe it's because of the force sensor you have on top of the picture. A force sensor needs to be placed in line with the a...

plus d'un an il y a | 0

A répondu
Modeling condensation on walls using Simscape Moist Air
Starting R2022b, the Pipe block in the Moist Air domain contains the "Effect of Condensation on Wall Surface". It's different f...

plus d'un an il y a | 1

| A accepté

A répondu
Thermal Liquid Tank in simscape
I don't think there is a more easy or efficient way in your case. In the latest version of Simscape, however, you can get up to...

plus d'un an il y a | 0

A répondu
Is it possible to create Packed bed thermal model in simscape?
Attempt to answer from 4 years later ... (1) I think the easiest way is to use a Pipe block. Attach the right amount of therm...

plus d'un an il y a | 0

A répondu
SimHydraulics - double centrifugal pump
The centrifugal pump block is available in Simscape Fluids for the Hydraulic domain since R2007a and for the newer Isothermal Li...

plus d'un an il y a | 1

A répondu
Pressure in a closed thermal liquid system
You'll need a "tank" to stablize this. What happens is that the density of the fluid is a function of pressure and temperatur...

plus d'un an il y a | 0

A répondu
I have confusion in Simscape Co2 transcritical system example. How you had designed compressor i dont get it and why you used PS LOOK UP TABLE 2D IN COMPRESSOR. Do i need a specific date to run this
The 2D LUT and an ideal flow rate source is to represent the BEHAVIOR of a compressor. If the pressure ratio (outlet/inlet) ris...

plus d'un an il y a | 0

A répondu
Looking for the base model of the counter balance valve
comment from 8 years later, lol. I don't think you can access the source code behind the blocks in Simscape Fluids (new product...

plus d'un an il y a | 0

A répondu
SimHydraulics "Failed to solve using iteration matrix. Initial conditions solve failed to converge."
Force sensor should be placed inline with there the force passes through, just like measuring a current. The force sensor in yo...

plus d'un an il y a | 0

A répondu
Hydraulic circuit between two pressure sources
The pressure sensor you have there blocks the flow totally, lol. It's like voltmeter where no current is let through. Usually ...

plus d'un an il y a | 0

A répondu
How to solve unconverged equations error ?
My experience: this typically happens when the piston moves while flow is constricted in the expanding chamber of the cylinder. ...

plus d'un an il y a | 0

A répondu
Adjust a Pressure Reducing Valve?
I am guessing, you are trying to build a valve block that will achieve any given pressure at its outlet? I think the best way t...

plus d'un an il y a | 0

A répondu
How does the Gate Valve (TL) block utilize "Cross-sectional area at ports A and B" and "Characteristic longitudinal length"?
In the latest version (R2022a), this characteristic length isn't a parameter anymore. In an earlier version (R2020b), I couldn'...

plus d'un an il y a | 0

A répondu
Simscape simulation of Hydraulic/Gas chamber
Maybe this will work: Use the TL-G tank and the insulators you mentioned. It should be able to do 1-4 and 6 of your requirement...

plus d'un an il y a | 0

A répondu
Simscape Fluids Valve models: Do they exhibit non-linearity too?
The Simscape valve components uses the spool position signal at the S port to determine the orifice areas (or dP-Q relationships...

plus d'un an il y a | 0

A répondu
Simulink/Simscape Model Interogation
Hi Brett, I think we have discussed this during a meeting. Just put some notes here so more people may benefit from your quest...

plus d'un an il y a | 0

A répondu
Cant implement the heat exchanger (simscape library) in an existing simulink model
You probably need a few (Controlled) Reservoir (TL)blocks to prescribe the pressure and temperature boundary conditions, and a C...

plus d'un an il y a | 0

A répondu
Simulink Thermal Hydraulic systems specify elevation
I would recommend that you try the Tank (TL) and Pipe (TL) from the Simscape Fluids library. Both allow you to specify an eleva...

plus d'un an il y a | 0

A répondu
Customized Simscape convective heat transfer component not working
Hi Roland, I believe you are missing one equation to define how Q is related to the heat flow through the ports. Try adding th...

plus d'un an il y a | 0

| A accepté

A répondu
Trapped air in fluid
The entrained air affects how the bulk modulus (hence also density) changes as a function of the pressure. More air will make t...

plus d'un an il y a | 0

A répondu
Dynamic calculating of kinematic viscosity
The source code of all Simscape foundation library blocks are available, including the hydraulic domain. I can verify back to t...

plus d'un an il y a | 0

A répondu
What would be the total flow rate inside the hydraulic cylinder chamber when modeled with piston chamber and hydro-mechanical converter?
The first a few paragraphs of the documentaion pages for theTranslational Mechanical Converter (IL) and the Translational Hydro-...

plus d'un an il y a | 0

A répondu
How to move the rod of a cylinder?
So far, the only way in Simscape to prescribe a mechanical motion is using a velocity source, while in Simscape Multibody, the o...

plus d'un an il y a | 0

A répondu
Specific and ideal pressure and flow
In general, one cannot prescribe both the pressure at and the flow through a node at the same time. If a pressure is prescribed...

plus d'un an il y a | 0

A répondu
Water supply system-Simulink
Depending on what physical domain you are thinking of, a few pipeline blocks in the Simscape Fluids library allow the modeling o...

plus d'un an il y a | 0

A répondu
How to control simscape ball valve block
Looks like an earlier version of question: https://www.mathworks.com/matlabcentral/answers/502708-control-of-ball-valve?s_tid=s...

plus d'un an il y a | 0

A répondu
Simscape 2P: How can I realize both varying local restriction and blocking the flow path.
Besides from my comment earlier, I've found that using a custom block of a "variable flow resistance" seems to make thing easier...

plus d'un an il y a | 0

A répondu
Optimal components for a two-stage heat pump in Simscape
It puzzles me why there isn't a flow out of the BV port of the tank. There isn't a flow into BV port either? The BV port is co...

plus d'un an il y a | 1

A répondu
Simscape Pipe array (many pipes in parallel)
It's possible to do it in the way you described. I attached a sample of "flow multiplier" and "thermal liquid multiplier". Dep...

plus d'un an il y a | 0