Community Profile

photo

Artyom


Last seen: presque 3 ans il y a |  Actif depuis 2013

Followers: 0   Following: 0

Contact

Statistiques

  • First Answer

Afficher les badges

Feeds

Afficher par

A répondu
Why is my Virtual bus coded as a structure?
Hello, I'm using R2018B and have the same problem. My buses are originating from Stateflow and non-virtual by default. They cre...

plus de 4 ans il y a | 0

Question


How to make generated code from stateflow charts deterministic(e.g execute same amount of time every timestep) to get worst case execution time (WCET)?
Hi there. Many of us deploy automatically generated code from Stateflow charts on real-time targets. Usually this code is exe...

plus de 4 ans il y a | 1 réponse | 0

0

réponse

Question


Multiple instances of randi in Stateflow generate same sequence of numbers
Hello I have multiple instances of randi function call in my chart and the problem is that randi produces exaclty same sequence...

plus de 4 ans il y a | 1 réponse | 0

1

réponse

Question


Use generated code from Simulink Model in Thingspeak
Hello I know, that it should be possible to use Simulink-generated code at the edge, which would work with ThingSpeak Data. B...

plus de 4 ans il y a | 2 réponses | 1

2

réponses

Question


Simulink Real-Time and non-Speedgoat Machine
Hello dear MATLAB community I would like to know if it is possible to use Simulink Real-Time with conventional PC as a target m...

plus de 4 ans il y a | 4 réponses | 5

4

réponses

Question


Is it possible to add EtherCAT Master to Raspberry Pi Simulink Support Package?
EtherCAT is a simple way to extend I/O capabilities of Raspberry Pi. Is it possible to add EtherCAT master block to Raspberry Pi...

environ 6 ans il y a | 1 réponse | 1

1

réponse

Question


What is the best way to observe signals of Simulink Embedded Coder Application in Matlab, running in real-time on target?
Hello, We use Simulink/Embedded Coder to generate deployable code, running on embedded target in hard real-time (2-10ms cycle)...

plus de 6 ans il y a | 1 réponse | 0

0

réponse

Question


Is there any option to view model signals, when generated code from model runs on final target hardware?
I'm using Embedded Coder to generate code from Simulink Models and run it on our target hardware. My hardware is high level enou...

plus de 7 ans il y a | 1 réponse | 0

0

réponse

Question


rtIOStreamBlockingSend and rtIOStreamBlockingRecv functions
Hi. I'm trying to implement Host/Target Communication using serial transfer. I used a guide from http://www.mathworks.de/de/...

presque 10 ans il y a | 1 réponse | 0

0

réponse

Question


Host/Target Communication and Production Code Generation
Hi Mathworks, We are using Simulink and Embedded Coder to simulate and generate C code from Models for our control platform. ...

presque 10 ans il y a | 1 réponse | 0

0

réponse

Question


What is the best way to call hardware driver function only on signal change in Simulink?
Hi. We are using Simulink Coder and Embedded coder to deploy simulink stateflow models in our control systems. The problem the...

environ 10 ans il y a | 1 réponse | 0

0

réponse

Question


How to show requirement details in System Requirements box?
I'm linking Simulink with Requirement management in JIRA using Validation and Verification Toolbox.. So far everything goes good...

plus de 10 ans il y a | 1 réponse | 0

0

réponse