James

Techsource Systems

Actif depuis 2011

Followers: 0 Following: 0

Message

Professional Interests: Control Systems, Physical Modeling, Robotics

Statistiques

All

RANG
14 760
of 297 613

RÉPUTATION
2

CONTRIBUTIONS
7 Questions
6 Réponses

ACCEPTATION DE VOS RÉPONSES
42.86%

VOTES REÇUS
0

Afficher les badges

Feeds

Question

How do I create tabs for codes already generated using GUIDE?
I've used Matlab GUIDE to construct a GUI and its automated callback functions. I would like to separate them into tabs, how...

presque 10 ans il y a | 1 réponse | 0

0

réponse

Réponse apportée
how to mate pin with a curved slot ?- Simmechanics
An example model here: http://www.mathworks.com/matlabcentral/fileexchange/50651-cam-gear-actuated-lever

presque 10 ans il y a | 0

| A accepté

Question

how to mate pin with a curved slot ?- Simmechanics
<</matlabcentral/answers/uploaded_files/27244/Picture1.png>> Hi all, I would like to mate the lever (with a pin) to the curve...

environ 10 ans il y a | 1 réponse | 0

1

réponse

Réponse apportée
Getting "Counter" Simulink block to switch direction?
Hope to get and answer for this too. I manage read the angular velocity from pulse reading but am stuck on how to detect direct...

presque 13 ans il y a | 0

Question

RTWT Not running real time
Hi, I ran a demo 'Real time vander pol simulation' (type 'rtvdp' on command prompt) on my desktop PC. However, after buildin...

plus de 13 ans il y a | 1 réponse | 0

0

réponse

Réponse apportée
xpctarget ping fails
Additional info: For both PCs I can ping from the DOS environment. Crossover cable is used. Direct connection between host and...

plus de 13 ans il y a | 0

Question

xpctarget ping fails
Hi, I have 2 target PCs - T1 and T2. I configured 'xpcexplr' and boot both PCs. (all configurations are the same but only ...

plus de 13 ans il y a | 3 réponses | 0

3

réponses

Question

Host target Communication lost once target PC is booted into the xPC environment
Hi all, The communication between my host and target PC is lost everytime I boot the target PC into the xPC environment. I'v...

plus de 13 ans il y a | 3 réponses | 0

3

réponses

Réponse apportée
Turning on grid on ltiviewer
Got it. Need to add 'on' after grid. For bode diagram the command 'grid' is executed twice. Hence, it's turned off. obj = f...

presque 14 ans il y a | 0

Réponse apportée
Turning on grid on ltiviewer
ooooppppss!!! How do I undo accepted answers?

presque 14 ans il y a | 0

Réponse apportée
Turning on grid on ltiviewer
Hi guys, I found a way but still not the best. The grid for Bode diagram is not displayed. Here's what I did; obj = findob...

presque 14 ans il y a | 0

Question

Turning on grid on ltiviewer
Hi everyone, I displayed 2 systems using ltiview as shown below: load ltiexamples ltiview({'step';'bode';'impulse';'nicho...

presque 14 ans il y a | 5 réponses | 0

5

réponses

Question

Error when running HEV model
Hi, I downloaded and tried running a HEV model from here: http://www.mathworks.com/matlabcentral/fileexchange/28441-hybrid-...

environ 14 ans il y a | 1 réponse | 0

1

réponse