Community Profile

photo

Manikandan


anna university

Last seen: 28 jours il y a |  Actif depuis 2012

Followers: 0   Following: 0

Contact

Professional Interests: Electric Drives

Statistiques

All
  • Explorer
  • Personal Best Downloads Level 1
  • First Review
  • 5-Star Galaxy Level 2
  • First Submission
  • Revival Level 3
  • First Answer

Afficher les badges

Feeds

Afficher par

A répondu
PI control techniques for speed control of a BLDC motor
Try to use trial and error method

environ 6 ans il y a | 0

A répondu
How to change Simulink model line widths
Don't take screen shoot. Go to edit, then copy model to clipboard. after past it as picture in your word. hence the quality of p...

presque 8 ans il y a | 3

A soumis


Measure the Frequency of given input Square wave
Contact: electricmani@yahoo.co.in

environ 8 ans il y a | 3 téléchargements |

Thumbnail

A répondu
how to control the position of a DC motor by FLC
i completed the same, refer this link, if you want more clarification write me: electricmani@yahoo.co.in http://ieeexplore.ie...

environ 8 ans il y a | 0

A répondu
Why is the induction motor speed very low and at a negative value
set your scope parameter setting, uncheck limited data points. reduce torque as zero.

environ 8 ans il y a | 0

A répondu
How to control a brushless motor through a ESC with C2000 using "Embedded Coder" Library in Simulink
I did same like, write me: electricmani@yahoo.co.in

environ 8 ans il y a | 0

A répondu
i am unable to get proper operations at 10 KHz speed of the "Repeating Sequence" block of Simulink under SimPowerSystems/Control& Measurements Library. With time values [0 1e-4 1e-4] for values [0 1e-4 0] the output is zero when run for 1 sec.
For 10khz output, use time value: (0 (1/10e3) and amplitude value: (0 1), then use less sampling time in solver, typically 2e-6 ...

environ 8 ans il y a | 0

A répondu
Is this the proper way to implement PID for 3 Phase inverter induction motor speed control?
Lot of theoretical methods available to find KP, Ki and Kd values, my suggestion for beginner try to do trial and error method. ...

environ 8 ans il y a | 0

A répondu
speed control of dc motor using SMC
First start open loop control of motor, verify with closed loop conventional PID controller, then change into SMC.

environ 8 ans il y a | 0

A répondu
Use PWM to control Speed of brushless dc motor!
use AND gate instead of product block. for more details contact me: electricmani@yahoo.co.in

plus de 8 ans il y a | 1

A répondu
how to find the setpoint ref input block in simlink for design of PI controller to control speed of servo motor... i can't find the setpoint bock in simulink.... setpoint ref input block...
use constant block

plus de 8 ans il y a | 2

A répondu
i want to control speed of DC motor using arduino via matlab.
use PWM

plus de 8 ans il y a | 0

A répondu
Single phaseInduction motor speed control
Your problem?

plus de 8 ans il y a | 0

A répondu
how to do simulation of speed control of three phase induction motor by v/f method
Contact me: electricmani@yahoo.co.in

plus de 8 ans il y a | 1

A répondu
How to implement speed control of induction motor using Fuzzy logic
Contact me: electricmani@yahoo.co.in

plus de 8 ans il y a | 0

A répondu
How to specify time values and Output values for sawtooth waveform?
Time: [0 2.5000e-005] Output: [0 1]

plus de 8 ans il y a | 0

A répondu
Tuning a pid controller. sampling times must agree?
Motor modeled as mathematical or taken from simpower system tool.

plus de 8 ans il y a | 0

A répondu
Fixed Step Solver Problems
Reduce your sample time as much as possible to small.

plus de 8 ans il y a | 0

A répondu
calculation of time difference between two crossings of voltage waveforms in simulink
Refer my paper: http://www.ripublication.com/ijaer_spl/ijaerv10n10_59.pdf

plus de 8 ans il y a | 0

A répondu
How to determine the controller parameters for BLDC drive?
Refer slandered control system books for ZN method.

plus de 8 ans il y a | 0

A répondu
torque ripple minimisation for bldc motor using direct torue control and indirect flux control
you need to mathematical modeling of motor.

plus de 8 ans il y a | 1

A répondu
there is a built in model of brushless DC motor in simulink library. does anyone know the equations used for built in model of BLDC.
like it.

plus de 8 ans il y a | 0

A répondu
Hi, i want to build an bldc motor in motor in matlab , i dont want to use an inbuilt motor block present in simulink .
I tried mathematical modeling of BLDC, but its result differ from simulik library BLDC motor. anybody have clear idea, post here...

plus de 8 ans il y a | 0

A répondu
Servo motor controlling using MATLAB
Yes possible, but you need MATLAB supported hardware. what's your platform wish to work.

plus de 8 ans il y a | 0

A répondu
Ball Screw driven XY table using AC servo motor.
Contact me @ electricmani@yahoo.co.in

plus de 8 ans il y a | 0

A répondu
how to calculate parameters for dc servo motor simulation?
you should contact manufacture or google it to find required data's. not possible to find required data from the available data....

plus de 8 ans il y a | 0

A répondu
Control Servo Motor
use analog output from the real time windows target tool box and select your DAQ via USB. then generate analog output voltage to...

plus de 8 ans il y a | 0

A répondu
Tacho feedback in a servo
If you use simulink for DC motor position control, use motor output speed wm in rad/sec from measurement block. convert equivale...

plus de 8 ans il y a | 0

A répondu
In which location ,we have to store the .fis file?
We need to import the file from work space or call where it was stored, before need to export designed fis to work space. me too...

plus de 8 ans il y a | 0

A répondu
quadrature/rotary encoder .mdl file
I did the same things, if need help contact me on electricmani@yahoo.co.in

plus de 8 ans il y a | 0

Charger plus