Réponse apportée
How can i add an equation to a block (impedance measurement)?
You have 2 options. If it is a static value of impedance, you can pre calculate your circuit parameters such as R = R_pu*Length...

11 mois il y a | 0

Réponse apportée
Is it possible to model a john bedini motor ?
You can do that using the simscape electrical tool. There is free training to get started: https://matlabacademy.mathworks.com/...

11 mois il y a | 0

Réponse apportée
Voltage Swell from Signal Builder
You can hook the signal builder block into a controlled voltage source.

11 mois il y a | 0

Réponse apportée
Simulink Load Flow Analysis for Electric Fleet Charging Station
Load flow for this tool was designed specifically for AC systems. While it does support single phase and unbalanced lines, this...

11 mois il y a | 0

Réponse apportée
unbalanced load on a synchronous generator
I tested these blocks and they don't seem to work well when split into a three phase load like this (even for a balanced load). ...

11 mois il y a | 0

Réponse apportée
tapping of secondary delta transformer
Please look at this block as a starting point: https://www.mathworks.com/help/sps/ref/tapchangingtransformer.html you can get f...

11 mois il y a | 0

Réponse apportée
Hello. If I have included delays in my code for my controller, how do I implement it so that the delays are considered when the code is executed?
The correct way to simulate a digital controller, so that you are incorporating the delay of the digital system is to utilize so...

11 mois il y a | 0

Réponse apportée
Breakdown Voltage (BDV) Tester for Transformer Oil
Hello Hatim, you don't actually ask a question or share model details. If you still want help, please ask a specific question ...

11 mois il y a | 0

Réponse apportée
While Opearting a N channel MOSFET in MATLAB with 100VDC, 100 Ohm load. the MOSFET only allowing 0.2A in each condition but I am expecting of 1A.
Increasing the mosfet threshold voltage will make it conduct less, not more. You need to parameterize the mosfet correctly. In...

11 mois il y a | 0

Réponse apportée
How can I create a simulation that supplies power to the motor by connecting fuel cells, dc-dc converters, and supercapacitors?
This really depends on how much detail you need for the converter. In general, when doing powertrain analysis, you don't need t...

11 mois il y a | 0

Réponse apportée
Different Thyristor Gate width gives different waveforms.
Are you sure the results are wrong? You don't have a dc-link capacitor to maintain the dc voltage and with the inductive load a...

12 mois il y a | 0

Réponse apportée
Better solver for simscape power electronics simulation
You can set your absolute tolerance to be the same as your relative tolerance, and uncheck the option for absolute tolerance. T...

environ un an il y a | 0

Réponse apportée
Table based battery block choices
You need to have either Simscape Battery or Simscape Electrical installed to have access to the table based battery. Please see...

environ un an il y a | 0

Réponse apportée
Inconsistent results when simulating an LC series circuit with SimScape
He issue is that the Adams solver is specifially for non-stiff problems and your problem being in simscape is typically a stiff ...

environ un an il y a | 0

Réponse apportée
Error while running Simulink
This happens when a model has extermely small time constants or challenging equations to solve. That usually means the model is...

environ un an il y a | 0

Réponse apportée
Thermofluid simulation of an electric motor
This is one starting point: https://www.mathworks.com/help/simscape/ug/motor-thermal-circuit.html and here is another: https://...

environ un an il y a | 0

Réponse apportée
sic mosfet SPICE models.lib file into Simulink using subcircuit2ssc
Wolfspeed specifically provides LTspice models which use a proprietary interface that is not always compatible with base SPICE. ...

environ un an il y a | 0

Réponse apportée
Exporting a simulink/Mathlab model as a circuit element for simulation software (Pspice/Cadence)
There are a few options. I am listing them by order of cost (cheapest to most expensive) You can try and utilize the co-simula...

environ un an il y a | 1

Réponse apportée
PV Mppt constant output voltage
the goal of mppt is to get the optimal power extraction of a solar panel. To accomplish this, the voltage and current must vary...

environ un an il y a | 1

| A accepté

Réponse apportée
Sample time relation of controller and PWM switching frequecny
Hello, you are correct that the most common approach is to have the switching frequency be the same as the control frequency. ...

environ un an il y a | 1

Réponse apportée
How can I export my Simulink electrical circuit into a Matlab function?
The easiest approach to this would be to utilize the sim() command. This lets you set parameters, run a simulation and then get...

environ un an il y a | 0

Réponse apportée
How can i implement BLDC commutation logic block to a PWM Module?
Please start with this page: https://www.mathworks.com/solutions/electrification/bldc-motor-control.html at the bottom are lin...

environ un an il y a | 0

| A accepté

Réponse apportée
Graphs are paused during simulation in Simulink and do not resume once RLC load is added via circuit breaker
It sounds like the simulation is "hanging" aka, it starts taking such small time steps that nothing appears to be happening. Thi...

environ un an il y a | 0

Réponse apportée
How can I connect my dynamic (mathematical) model of inverter to the grid simulink model?
the most common way to to attatch it to controlled voltage sources for the inverter output and use a controlled current source f...

plus d'un an il y a | 0

Réponse apportée
Slip in Asynchronous Block - Induction Machine Squirrel Cage
the block can only give you input for the initial condition of slip, but this does not determine your slip once the model is run...

plus d'un an il y a | 0

| A accepté

Réponse apportée
How the voltage based active cell balancing model works for larger voltage difference and not working for smaller voltage difference ?
You are modelling lithium ion batteries and giving them different nominal voltages. These batteries are not linear and would no...

plus d'un an il y a | 0

Réponse apportée
unable to resolve cooling plate error
I think you need to set your number of nodes to 14 and not 14x14 for the cooling plate. If that doesn't solve it, please share ...

plus d'un an il y a | 0

| A accepté

Réponse apportée
How to import .SUBCKT Spice model into MATLAB Simscape?
Unfortunately, there is no guarentee that an imported pspice model will work in simscape. It sounds like you used the command c...

plus d'un an il y a | 0

Réponse apportée
How can I gate-off the Average-Value VSC block ?
This will be easier to do with a slightly different block, the Converter (Three Phase). You can set this block to averaged swit...

plus d'un an il y a | 0

Réponse apportée
Help me finish the scheme in MATLAB
This issue is that because an ideal transformer is used, it is perfectly isolated from the rest of the circuit. Unfortunately, ...

plus d'un an il y a | 1

| A accepté

Charger plus