owen chang
Followers: 0 Following: 0
Statistiques
9 Questions
0 MATLAB Answers
RANG
37 524
of 289 769
RÉPUTATION
1
CONTRIBUTIONS
9 Questions
0 MATLAB Answers
ACCEPTATION DE VOS RÉPONSES
22.22%
VOTES REÇUS
1
RANG
of 19 586
RÉPUTATION
N/A
CLASSEMENT MOYEN
0.00
CONTRIBUTIONS
0 Fichier
TÉLÉCHARGEMENTS
0
ALL TIME TÉLÉCHARGEMENTS
0
RANG
of 144 154
CONTRIBUTIONS
0 Problèmes
0 Solutions
SCORE
0
NOMBRE DE BADGES
0
CONTRIBUTIONS
0 Publications
CONTRIBUTIONS
0 Public Chaîne
CLASSEMENT MOYEN
CONTRIBUTIONS
0 Point fort
NOMBRE MOYEN DE LIKES
Feeds
Question
why exportONNXNetwork will add additional "Sub" in onnx, how to remove this layer in onnx?
Hi, i did the following: >> baseNetwork = resnet50; >> exportONNXNetwork(baseNetwork,'resnet50-matlab'); but when compare sam...
plus de 4 ans il y a | 1 réponse | 0
1
réponseQuestion
how to deploy deep learning prototype to FPGA using HDL Coder?
Hi i have FPGA platform and like to play around with Matlab deep learning (like MatConvNet), then deploy on my FPGA platform fo...
plus de 6 ans il y a | 1 réponse | 0
1
réponseQuestion
running open_system('hdlcoder_led_blinking') for zynq, but no connection?
Hi, i am using usb jtag cable for communication with zynq-zc702, but i can't see serialport as instructed in the webinar, how sh...
plus de 10 ans il y a | 1 réponse | 0
1
réponseQuestion
how could i generate an axi-stream or axi4-lite dma master by hdl coder?
Hi, i found the current demo using only axi-stream slave interface in sobel image processing system. however, it might require a...
plus de 10 ans il y a | 1 réponse | 0
1
réponseQuestion
HDL Stream FFT in HDL Coder 2013b, not support AXI4-Stream Interface? (single rate?)
Hi, i have built a system involving Stream FFT with AXI4-Stream Interface, the goal is to put this design into Zynq, so AXI4-St...
plus de 10 ans il y a | 1 réponse | 0
1
réponseQuestion
Failed Streaming interface is not supported when the DUT is not single rate
Hi, the AXI-Stream interface for Stream FFT is requiring DUT "single rate", but i can't find where to set it, and what does it ...
plus de 10 ans il y a | 1 réponse | 0
0
réponseQuestion
HDL Stream FFT in HDL Coder 2013b, not support FPGA?
Hi, i am using Stream FFT for Zynq, but once i have created the subsystem and set it to Atomic, i have this error message pop u...
plus de 10 ans il y a | 1 réponse | 0
1
réponseQuestion
How to create a FFT ipcore for Zynq using Simulink HDL Coder?
there is an error message "not support for frame based module"? is there any other solution for exporting signal processing bl...
plus de 10 ans il y a | 2 réponses | 1
2
réponsesQuestion
Does HDL coder from Simulink support AXI-4 Stream Interface for Xilinx Zynq?
Hi all, I have created an adder example and export to Xilinx Vivado 2013.2 using HDL coder, and integrated using Vivado IPI. th...
plus de 10 ans il y a | 1 réponse | 0