Peripheral Management
Before communicating with target hardware, first apply block settings, hardware configuration parameters and the peripheral app settings.
Blocks
Tools
| SoC Builder | Build, load, and execute multicore application models on Infineon AURIX TC4x hardware boards (Since R2024b) |
| Hardware Mapping | Map tasks and peripherals in a model to hardware board configurations (Since R2022b) |
| Digital Port Read Peripheral Configuration | Map Digital Port Read peripherals in the Infineon AURIX model to peripheral registers in the MCU (Since R2024a) |
| Digital Port Write Peripheral Configuration | Map Digital Port Write peripherals in the Infineon AURIX model to peripheral registers in the MCU (Since R2024a) |
| Tasks | Map tasks in the Infineon AURIX to interrupt service routines on the hardware board (Since R2024a) |
| Encoder Peripheral Configuration | Map encoder peripherals in the Infineon AURIX model to peripheral registers in the MCU (Since R2024a) |
| EVADC Peripheral Configuration | Map EVADC peripherals in the Infineon AURIX model to peripheral registers in the MCU (Since R2024a) |
| PWM Peripheral Configuration | Map PWM peripherals in the Infineon AURIX model to peripheral registers in the MCU (Since R2024a) |
| QSPI Controller Peripheral Configuration | Map QSPI controller peripherals in the Infineon AURIX model to peripheral registers in the MCU (Since R2024a) |
| QSPI Peripheral Configuration | Map QSPI peripherals in the Infineon AURIX model to peripheral registers in the MCU (Since R2024a) |
| EDSADC Peripheral Configuration | Map EDSADC peripherals in Infineon AURIX model to peripheral registers in MCU (Since R2024b) |
| SENT Configuration | Map data transfer over SENT protocol in the Infineon AURIX model to peripheral registers in the MCU (Since R2024b) |
| MCAN Transmit Peripheral Configuration | Map peripherals of MCAN Transmit block in the model to peripheral registers in MCU (Since R2025a) |
| MCAN Receive Peripheral Configuration | Map MCAN Receive peripherals in the model to the peripheral registers in MCU (Since R2025a) |
Model Settings
Topics
- Run Model on Virtual Prototyping (VP)
Run your model on virtual prototyping without the hardware using the Synopsys Virtual Prototyping (VP) Virtualizer.
- Processor-in-the-Loop (PIL) Simulation
Test the code generated from top models, referenced models, or subsystems on Infineon AURIX TC3x microcontrollers.
- External Mode Simulation for Signal Monitoring and Parameter Tuning
Tune parameters and monitor signals through communication channel between development computer and Infineon AURIX TC3x microcontroller.
- Get Started with IO Device Builder
Understand system requirements and work with IO Device Builder.
Featured Examples
Getting Started with Embedded Coder Support Package for Infineon AURIX TC3x Microcontrollers
Use Embedded Coder® Support Package for Infineon® AURIX™ TC3x Microcontrollers to run a Simulink® model on Infineon AURIX TC3x board.
Getting Started with QSPI Communication for Infineon AURIX TC3x Microcontrollers
The use the QSPI Controller and QSPI Peripheral blocks from Embedded Coder® Support Package for Infineon® AURIX™ TC3x Microcontrollers to handle data through interrupts.
Code Verification and Validation with PIL
Use Embedded Coder® Support Package for Infineon AURIX™ TC3x Microcontrollers for code verification and validation using PIL.
Signal Monitoring and Parameter Tuning Using Infineon AURIX TC3x Microcontrollers
Use Embedded Coder® Support Package for Infineon® AURIX™ TC3x Microcontrollers in Monitor and Tune mode (External mode) using Infineon AURIX TC3x hardware board.
Field-Oriented Control of BLDC with Encoder Using Infineon AURIX TC3xx Microcontrollers
Implement the field-oriented control (FOC) technique to control the speed of a three-phase brushless DC (BLDC) motor. The FOC algorithm requires rotor position feedback, which is obtained by using an encoder sensor. For more details about FOC, see Field-Oriented Control (FOC) (Motor Control Blockset).
Extrapolate EDSADC Output Using Timestamp Information
Use the Enhanced Delta-Sigma Analog to Digital Converter (EDSADC) block from Embedded Coder® Support Package for Infineon® AURIX™ TC3x Microcontrollers to determine the accurate EDSADC output using its timestamp information.
Create UART Loopback Block Using IO Device Builder App
Use the IO Device Builder app to create a UART Loopback block to read and transmit serial data to an SSH utiity (PuTTY).
Create UART Transmit Block to Transmit Serial Data Using IO Device Builder App
Use the IO Device Builder app to create a UART Transmit block and transmit data to a serial port.
PIL Simulation for AUTOSAR Software Component with Infineon AURIX TC3x Microcontroller
Use Embedded Coder® Support Package for Infineon AURIX™ TC3x Microcontrollers for code verification and validation of AUTOSAR component models using PIL. This example uses Simulink® models with Infineon AURIX TC3x board mapped to a classic AUTOSAR software component, generating code that complies with the AUTOSAR standard.
