DFECDR
Decision feedback equalizer (DFE) with clock and data recovery (CDR)
Libraries:
SerDes Toolbox /
Datapath Blocks
Description
The DFECDR block adaptively processes a sample-by-sample input signal or analytically processes an impulse response vector input signal to remove distortions at post cursor taps.
The DFE modifies baseband signals to minimize the intersymbol interference (ISI) at the clock sampling times. The DFE samples data at each clock sample time and adjusts the amplitude of the waveform by a correction voltage.
For impulse response processing, the hula-hoop algorithm is used to find the clock sampling locations. The zero-forcing algorithm is then used to determine the N correction factors necessary to have no ISI at the N subsequent sampling locations, where N is the number of DFE taps.
For sample-by-sample processing, the clock recovery is accomplished by a first order phase tracking and optionally second order frequency tracking model. The bang-bang phase detector utilizes the unequalized edge samples and equalized data samples to determine the optimum sampling location. The DFE correction voltage for the N-th tap is adaptively found by finding a voltage that compensates for any correlation between two data samples spaced by N symbol times. This requires a data pattern that is uncorrelated with the channel ISI for correct adaptive behavior.
Ports
Input
WaveIn — Input baseband signal
scalar | vector
Input baseband signal. The input signal can be a sample-by-sample signal specified as a scalar, or an impulse response vector signal.
Data Types: double
Output
WaveOut — Estimated channel output
scalar | vector
Estimated channel output. If the input signal is a sample-by-sample signal specified as a scalar, the output is also scalar. If the input signal is an impulse response vector signal, the output is also a vector.
Data Types: double
Parameters
DFE
Mode — DFE operating mode
Adapt
(default) | Off
| Fixed
DFE operating mode:
Off
— DFECDR is bypassed and the input waveform remains unchanged.Fixed
— DFECDR applies the input DFE tap weights specified in Initial tap weights (V) to the input waveform.Adapt
— The Init subsystem calls to the DFECDR System object™. The DFECDR System object finds the optimum DFE tap values for the best eye height opening for statistical analysis. During time domain simulation, DFECDR uses the adapted values as the starting point and applies them to the input waveform. For more information about the Init subsystem, see Statistical Analysis in SerDes Systems.
Programmatic Use
Use
get_param(gcb,'Mode')
to view the current DFECDR Mode.Use
set_param(gcb,'Mode',value)
to set DFECDR to a specific Mode.
Initial tap weights (V) — Initial DFE tap weights
[0 0 0 0]
(default) | row vector
Initial DFE tap weights, specified as a row vector in volts. The length of the vector specifies the number of DFE taps. The vector element value specifies the strength of the tap at that element position. Setting a vector element value to zero only initializes the tap.
You can use a valid MATLAB expression to evaluate the Initial tap weights (V) row vector.
Example: set_param(gcb,'TapWeights',"zeros(1,100)")
creates a
DFE with 100 taps.
Programmatic Use
Use
get_param(gcb,'TapWeights')
to view the current value of DFECDR Initial tap weights (V).Use
set_param(gcb,'TapWeights',value)
to set DFECDR to a specific Initial tap weights (V) vector value.
Data Types: double
Adaptive gain — Controls DFE tap weight update rate
9.6e-5
(default) | positive real scalar
Controls DFE tap weight update rate, specified as a unitless positive real scalar. Increasing the value of Adaptive gain leads to a faster convergence of DFE adaptation at the expense of more noise in DFE tap values.
Programmatic Use
Use
get_param(gcb,'EqualizationGain')
to view the current DFECDR Adaptive gain value.Use
set_param(gcb,'EqualizationGain',value)
to set DFECDR to a specific value of Adaptive gain.
Data Types: double
Adaptive step size (V) — DFE adaptive step resolution
1e-06
(default) | nonnegative real scalar | nonnegative real-valued row vector
DFE adaptive step resolution, specified as a nonnegative real scalar or a nonnegative real-valued row vector in volts. Specify as a scalar to apply to all the DFE taps or as a vector that has the same length as the Initial tap weights (V).
Adaptive step size (V) specifies the minimum DFE tap change
from one time step to the next to mimic hardware limitations. Setting
Adaptive step size (V) to 0
yields DFE tap
values without any resolution limitation.
Programmatic Use
Use
get_param(gcb,'EqualizationStep')
to view the current DFECDR Adaptive step size (V) value.Use
set_param(gcb,'EqualizationStep',value)
to set DFECDR to a specific value of Adaptive step size (V).
Data Types: double
Minimum DFE tap value (V) — Minimum value of adapted taps
-1
(default) | real scalar | real-valued row vector
Minimum value of the adapted taps, specified as a real scalar or a real-valued row vector in volts. Specify as a scalar to apply to all the DFE taps or as a vector that has the same length as the Initial tap weights (V).
Programmatic Use
Use
get_param(gcb,'MinimumTap')
to view the current DFECDR Minimum DFE tap value (V) value.Use
set_param(gcb,'MinimumTap',value)
to set DFECDR to a specific value of Minimum DFE tap value (V).
Data Types: double
Maximum DFE tap value (V) — Maximum value of adapted taps
1
(default) | nonnegative real scalar | nonnegative real-valued row vector
Maximum value of the adapted taps, specified as a nonnegative real scalar or a nonnegative real-valued row vector in volts. Specify as a scalar to apply to all the DFE taps or as a vector that has the same length as the Initial tap weights (V).
Programmatic Use
Use
get_param(gcb,'MaximumTap')
to view the current DFECDR Maximum DFE tap value (V) value.Use
set_param(gcb,'MaximumTap',value)
to set DFECDR to a specific value of Maximum DFE tap value (V).
Data Types: double
2x tap weights — Multiply DFE tap weights by a factor of two
off (default) | on
Select to multiply the DFE tap weights by a factor of two.
The output of the slicer in the DFECDR block from the SerDes Toolbox™ is [-0.5 0.5]. But some industry applications require the slicer output to be [-1 1]. 2x tap weights allows you to quickly double the DFE tap weights to change the slicer reference.
CDR
CDR Mode — Determine CDR order
1st order
(default) | 2nd order
Determine the CDR order to enable phase and frequency tracking.
1st order
— Only tracks the phase.2nd order
— Tracks both the phase and frequency.
Programmatic Use
Block parameter:
CDRMode |
Type: character vector |
Values:
1st order | 2nd
order |
Default:
1st order |
Phase Detector — Clock phase detector option
BangBang
(default) | BaudRateTypeA
Clock phase detector option used in the clock data recovery. You can choose between bang-bang (Alexander) or baud-rate type-A (Mueller-Muller).
Programmatic Use
Block parameter:
PhaseDetector |
Type: character vector |
Values:
BangBang |
BaudRateTypeA |
Default:
BangBang |
Phase Offset (symbol time) — Clock phase offset
0
(default) | real scalar in the range [-0.5,0.5]
Clock phase offset, specified as a real scalar in the range [-0.5,0.5] in fraction of symbol time. Phase Offset is used to manually shift clock probability distribution function (PDF) for better bit error rate (BER).
Programmatic Use
Block parameter:
PhaseOffset |
Type: character vector |
Values: real scalar in the range [-0.5,0.5] |
Default:
0 |
Data Types: double
Reference offset (ppm) — Reference clock offset impairment
0
(default) | real scalar in the range [0, 300]
Reference clock offset impairment, specified as a real scalar in the range [0, 300] in parts per million (ppm). Reference offset (ppm) is the deviation between transmitter oscillator frequency and receiver oscillator frequency.
Programmatic Use
Block parameter:
ReferenceOffset |
Type: character vector |
Values: real scalar in the range [0, 300] |
Default:
0 |
Data Types: double
Early/late count threshold — Early or late CDR count threshold to trigger phase update
16
(default) | real positive integer ≥5
Early or late CDR count threshold to trigger a phase update, specified as a unitless real positive integer ≥5. Increasing the value of Early/late count threshold provides a more stable output clock phase at the expense of convergence speed. Because the bit decisions are made at the clock phase output, a more stable clock phase has a better bit error rate (BER).
Early/late count threshold also controls the bandwidth of the CDR.
Programmatic Use
Block parameter:
Count |
Type: character vector |
Values: real positive integer ≥5 |
Default:
16 |
Data Types: double
Step (symbol time) — Clock phase resolution
0.0078
(default) | real scalar
Clock phase resolution, specified as a real scalar in fraction of symbol time. Step (symbol time) is the inverse of the number of phase adjustments in CDR.
Programmatic Use
Block parameter:
Step |
Type: character vector |
Values: real scalar |
Default:
0.0078 |
Data Types: double
Frequency tracking gain — Internal gain for frequency tracking
0.00048828125
(default) | nonnegative real scalar
Internal gain for the frequency tracking loop, specified as a nonnegative real scalar.
Dependencies
To enable this parameter, set the CDR Mode to
2nd order
.
Programmatic Use
Block parameter:
FrequencyStep |
Type: character vector |
Values: nonnegative real scalar |
Default:
0.00048828125 |
Data Types: double
Frequency tracking update — Frequency tracking update
16
(default) | nonnegative integer scalar
Once every Frequency tracking update symbols, update the system phase rotator clock with the frequency estimate.
Dependencies
To enable this parameter, set the CDR Mode to
2nd order
.
Programmatic Use
Block parameter:
FrequencyCount |
Type: character vector |
Values: nonnegative real scalar |
Default:
16 |
Data Types: double
Frequency step ramp — Number of symbol times required for initial internal frequency tracking gain to reach specified value
3000
(default) | nonnegative integer scalar
To help frequency tracking loop lock early in a simulation, the initial Frequency tracking gain starts at a high value of 1/(2*Frequency tracking update). Then the Frequency tracking gain gradually reduces to the specified value by roughly Frequency step ramp symbol times.
Dependencies
To enable this parameter, set the CDR Mode to
2nd order
.
Programmatic Use
Block parameter:
FrequencyStepRamp |
Type: character vector |
Values: nonnegative real scalar |
Default:
3000 |
Data Types: double
Sensitivity (V) — Sampling latch metastability voltage
0
(default) | real scalar
Sampling latch metastability voltage, specified as a real scalar in volts. If the data sample voltage lies within the region (±Sensitivity (V)), there is a 50% probability of bit error.
Programmatic Use
Block parameter:
Sensitivity |
Type: character vector |
Values: real scalar |
Default:
0 |
Data Types: double
Mode — Include Mode parameter in IBIS-AMI model
on (default) | off
Select to include Mode as a parameter in the IBIS-AMI file. If you deselect Mode, it is removed from the AMI files, effectively hard-coding Mode to its current value.
Tap weights — Include Tap weights parameter in IBIS-AMI model
on (default) | off
Select to include Tap weights as a parameter in the IBIS-AMI file. If you deselect Tap weights, it is removed from the AMI files, effectively hard-coding Tap weights to its current value.
Phase Offset — Include Phase Offset parameter in IBIS-AMI model
on (default) | off
Select to include Phase Offset as a parameter in the IBIS-AMI file. If you deselect Phase Offset, it is removed from the AMI files, effectively hard-coding Phase Offset to its current value.
Reference offset — Include Reference offset parameter in IBIS-AMI model
on (default) | off
Select to include Reference offset as a parameter in the IBIS-AMI file. If you deselect Reference offset, it is removed from the AMI files, effectively hard-coding Reference offset to its current value.
More About
Phase Detector Model
You can select which phase detector model the block uses in the clock recovery: bang-bang (Alexander) or baud-rate type-A (Mueller-Muller). To view the phase detector model used in Simulink®, you need to look under the mask of the block and double click the DFECDR System object to open the block parameter dialog box.
If the SerDes Designer exports a DFECDR block to Simulink that uses bang-bang phase detector model, the app automatically defines the
clock position. If you change the phase detector option to baud-rate type-A Simulink, you need to manually add the reserved parameter
Rx_Decision_Time
. To add the parameter, open the AMI-Rx tab of the
SerDes IBIS-AMI Manager dialog box. Adding reserved parameter also requires refreshing the
Init function. For more information, see Define Clock Position in Statistical Eye.
If the SerDes Designer exports a DFECDR block to Simulink that uses baud-rate type-A phase detector model, the app automatically uses
the reserved AMI parameter Rx_Decision_Time
in the AMI-Rx tab of the
SerDes IBIS-AMI Manager dialog box to define the clock position.
Version History
Introduced in R2019a
Commande MATLAB
Vous avez cliqué sur un lien qui correspond à cette commande MATLAB :
Pour exécuter la commande, saisissez-la dans la fenêtre de commande de MATLAB. Les navigateurs web ne supportent pas les commandes MATLAB.
Select a Web Site
Choose a web site to get translated content where available and see local events and offers. Based on your location, we recommend that you select: .
You can also select a web site from the following list:
How to Get Best Site Performance
Select the China site (in Chinese or English) for best site performance. Other MathWorks country sites are not optimized for visits from your location.
Americas
- América Latina (Español)
- Canada (English)
- United States (English)
Europe
- Belgium (English)
- Denmark (English)
- Deutschland (Deutsch)
- España (Español)
- Finland (English)
- France (Français)
- Ireland (English)
- Italia (Italiano)
- Luxembourg (English)
- Netherlands (English)
- Norway (English)
- Österreich (Deutsch)
- Portugal (English)
- Sweden (English)
- Switzerland
- United Kingdom (English)