Réponse apportée
Latency not working when platform is the target
Hey @Carlos, I was facing the same issue with MATLAB R2024a, and I have been using a similar workaround. I have upgraded to MA...

plus d'un an il y a | 0

Réponse apportée
Drone Project Accelerometer/Gyroscope Implementation
Hey @Methmika, The 'IMU' block in Simulink, bundles the accelerometer, gyroscope, and magnetometer into one block. You can l...

plus d'un an il y a | 0

Réponse apportée
Adsorption process in Simulink
Hi @Ababacar Thiam, To switch between the two subsystems (adsorption and desorption) based on a control signal, the ‘Switch’...

plus d'un an il y a | 0

| A accepté

Réponse apportée
g = decsg() multiple objects
Hi @Bastiaan, The unexpected result is due to the set formula being passed to the ‘decsg’ function. The attached example code...

plus d'un an il y a | 0

Réponse apportée
Trajectory of a 3d body
Hi Rakshit, In the code shared, I am assuming that 'theta' is the pitch angle of the projectile,'alpha' is the angle of attack,...

plus d'un an il y a | 0

| A accepté

Réponse apportée
Input and State Constraints in MPC problem solved by quadprog
Hi Angelo, The following procedure can be used to convert the state constraints into input constraints. Consider the discret...

plus d'un an il y a | 0

Réponse apportée
Problem returning arrays from a C Caller in Simulink
Hi Julien, I comprehend that you are trying to obtain a time-varying output from a “C Caller” block. This can be achieved in ...

plus d'un an il y a | 0

| A accepté

Réponse apportée
"Solver was unable to reduce the step size without violating the minimum step size value" in Simscape simulation
Hi David, The warning "Solver was unable to reduce the step size without violating the minimum step size value" could arise ...

plus d'un an il y a | 0

Réponse apportée
How do I track the centroid of a set of frames in simscape multibody?
Hey dst, I understand that your main objective is to create a frame in “Simscape Multibody” located at the centroid of few o...

plus d'un an il y a | 0

| A accepté

Réponse apportée
How can I add an XYplot to Simulink Data Inspector programmatically ?
Hello Pavan, I comprehend that you are trying to plot XY data from MATLAB on the “Simulink Data Inspector”. There are couple of...

plus d'un an il y a | 1

Réponse apportée
How to get acceleration plot ? floor acceleration , driver acceleration
Hello Abdullah, From the shared screenshot I comprehend that the displacements of the floor and driver are available, and th...

plus d'un an il y a | 0

Réponse apportée
Error in Modeling and Simulation of an Autonomous Underwater Vehicle matlab exemple
Hello Samuel, I am able to replicate the error, “Error in port widths or dimensions” arising when running the “Modeling and...

plus d'un an il y a | 0

Réponse apportée
Configuring 2x2 Antenna Setup with 2 CSI-RS Ports in MATLAB's 5G Toolbox for CQI Reporting Test Compliance
Hi Jake, I understand that you are facing errors when trying CSI-RS and antenna panel configuration that are not mentioned in ...

plus d'un an il y a | 0

Réponse apportée
Coordinate system or axis system
Hey Sagar, I see that you are trying to create a body (a plane) in a 3D axis and then moving the body along a trajectory. Yo...

plus d'un an il y a | 0

Réponse apportée
There was a serious error in the calculation of the satellite position
Hello Ruizhe, From the code you have shared, I can comprehend that you are creating a satellite simulation using the “satelli...

plus d'un an il y a | 1

Réponse apportée
Expressions for QP matrices
Hello Elias, I understand that you are trying to use the “quadprog” function in the “Optimization Toolbox” to implement an MPC ...

plus d'un an il y a | 0