Subplot no values at individual subplots

Hi,

do you know why there are no values for subplot 5 and seven?

Thanks in advance

clc
clear all
clear workspace 

%load('Punkt_113.mat')
load('Punkt_120.mat')
Punkt_120(1:2,:) = [];
% Punkt_113 = table2array(Punkt_113);
% Punkt_113 = split(Punkt_113,[" ", " "]); % double delimiters split
% Punkt_113
% CC(1:10,1:10) % show first 10 columns of first 10 rows 
% ans =   10×10 string array
% BHQ_113 = Punkt_113([1:10],[3:144]);
% HQ5000_113 = Punkt_113([1:10],[287:428]);
% HQextrem_113 = Punkt_113([1:10],[145:286]);
% HQ10000_113 = Punkt_113([1:10],[430:571]);
% 

Punkt_120 = table2array(Punkt_120);
Punkt_120 = split(Punkt_120,[" ", " "]);

% CCC=strrep(CC,',','.');
% Punkt_113=str2double(Punkt_113);
Punkt_120=str2double(Punkt_120);

BHQ_120 = Punkt_120([1:11],[4:145]);
HQ5000_120 = Punkt_120([1:11],[288:429]);
HQextrem_120 = Punkt_120([1:11],[146:287]);
HQ10000_120 = Punkt_120([1:11],[430:571]);
Koordinaten_120= Punkt_120([1:11], [1:3])
Z=  ones(11, 142);

A=[0:141]
% Z= 453.567 452.977 454.196  %Geländehöhe
for i=1:11
%     if rem(i-1, 5) == 0;
%              f = figure;
%     end

sgtitle('WSPL zeitlicher Verlauf Pegelpunkt FKM 120');
a(i)=subplot(10, 1, rem(i-1, 5)+1);
hold on;
[maxHQextrem,indexHQextrem]=max(HQextrem_120(i,:)- Koordinaten_120(i,3));
[maxHQ5000,indexHQ5000]=max(HQ5000_120(i,:)- Koordinaten_120(i,3));
[maxHQ10000,indexHQ10000]=max(HQ10000_120(i,:)- Koordinaten_120(i,3));

str = ['Maximaler Überlauf [m]: HQextrem ',num2str(maxHQextrem),' HQ5000 ',num2str(maxHQ5000),' HQ10000 ',num2str(maxHQ10000)];
b(i) = annotation('textbox','String',str,'Position',a(i).Position,'Vert','bottom','FitBoxToText','on');
hold on 
%annotation('textbox', 'String',str)
title(['Punkt ', num2str(i)]);
HQextrem_120(HQextrem_120<=(Z.*Koordinaten_120(i,3))-2)=nan;
HQ5000_120(HQ5000_120<=(Z.*Koordinaten_120(i,3))-2)=nan;
HQ10000_120(HQ10000_120<=(Z.*Koordinaten_120(i,3))-2)=nan;
BHQ_120(BHQ_120<=(Z.*Koordinaten_120(i,3))-2)=nan;

plot(A(1,:), BHQ_120(i,:))
hold on 
plot(A(1,:), HQextrem_120(i,:))
plot(A(1,:), HQ5000_120(i,:))
plot(A(1,:), HQ10000_120(i,:))

yline(Koordinaten_120(i,3))


leg=legend('BHQ','HQextrem','HQ5000', 'HQ10000', 'Geländehöhe');
title(leg,'WSPL');
newPosition = [0.92 0.65 0.05 0.2];
newUnits = 'normalized';
set(leg,'Position', newPosition,'Units', newUnits);
newcolors = {'#FF00FF','#7E2F8E','#0000FF','#00FFFF'};
colororder(newcolors)
xlabel('Zeit [h]');
ylabel('Höhe über NN [m]');
grid on 
set(gcf, 'Position', get(0, 'Screensize'));
end

[dpb]

You're setting a lot of stuff to NaN it appears; NaN aren't plotted so if the data for those particular plots turns out to all be NaN you won't see anything...or if just one or two scatter points aren't NaN, there may not be sufficient resolution that the individual pixels are visible.

Use the debugger and set a breakpoint to stop after the given loop index that is a problem and see what your arrays contain...if it plots some but not all, it's bound to be data-dependent upon those particular subsets.

[Frederik Reese]

When I plot another table there are no values on the same subplots. Because of this I think it is due to the coding.

Thanks for your answer

[dpb]

Well, the debugger is still your friend to figure out the logic error...