how to get one shape out of multiple shapes
Afficher commentaires plus anciens
Hi,
I have multiple shapes I need to merge into a single shape, because I have sets of shapes those I have to merge and compare with each other (put into a one plot).
the set of data is attached and I can plot it like this:
plot(X(:, [1:end 1])', Y(:, [1:end 1])')
let me know, if you know how to do it, thanks.
I got this shape using patch, but it generated a Patch file that I cannot use.
Ideally, I would like my data was interpolated so the final shape will not have sharp edges but be smooth and go down to Y=0.
Help me handle that too if you can. thanks

1 commentaire
Dyuman Joshi
le 13 Déc 2023
"I got this shape using patch, but it generated a Patch file that I cannot use."
You can't use the patch object or you can't use the output generated?
What is the expected output? It will be helpful if you can show an illustration.
Réponse acceptée
Plus de réponses (2)
Mathieu NOE
le 13 Déc 2023
hello
try this

x = double(X(:));
y = double(Y(:));
% remove nan
id = isnan(x) & isnan(y);
x(id) = [];
y(id) = [];
% k = boundary(___,s) specifies shrink factor s using any of the previous syntaxes.
% s is a scalar between 0 and 1. Setting s to 0 gives the convex hull,
% and setting s to 1 gives a compact boundary that envelops the points.
% The default shrink factor is 0.5.
s = 0.1;
k = boundary(x,y,s);
x_out = x(k);
y_out = y(k);
% find lower left "corner" point to make extrapolation towards Y = 0
[mx,ix1] = min(x_out);
my = y_out(ix1);
ind = find(x_out<(mx+1));
slope = mean(diff(y_out(ind))./diff(x_out(ind)));
x_lower_left = mx - my/slope;
% find lower right "corner" point to make extrapolation towards Y = 0
[mx,ix2] = max(x_out);
my = y_out(ix2);
ind = find(x_out>(mx-1));
slope = mean(diff(y_out(ind))./diff(x_out(ind)));
x_lower_right = mx - my/slope;
% add those two new points to x_out and y_out
x_out2 = [x_out(1:ix2-1); x_lower_right; x_out(ix2:ix1); x_lower_left; x_out(ix1+1:end) ] ;
y_out2 = [y_out(1:ix2-1); 0 ; y_out(ix2:ix1); 0 ; y_out(ix1+1:end) ] ;
plot(x,y, '*', x_out, y_out, '-*r', x_out2, y_out2, '-g')
Asliddin Komilov
le 15 Déc 2023
0 votes
7 commentaires
Mathieu NOE
le 19 Déc 2023
I got this shape if I still use your command
plot(X(:, [1:end 1])', Y(:, [1:end 1])')
- what do you want to do - simply close the top (flat ?)
- does your requirement "go down to Y=0" still holds ? (even though I cannot really figure out what it should be here )

Asliddin Komilov
le 19 Déc 2023
Image Analyst
le 19 Déc 2023
You might want to unaccept the answer because some people are probably going to skip over your question because they see it's been marked solved.
DGM
le 19 Déc 2023
It's not really clear to me what determines whether convexity and extrapolation are required.
I agree with @Image Analyst. If the question isn't answered, don't pick a solution that doesn't work.
Asliddin Komilov
le 20 Déc 2023
Modifié(e) : Asliddin Komilov
le 20 Déc 2023
Asliddin Komilov
le 20 Déc 2023
Modifié(e) : Asliddin Komilov
le 20 Déc 2023
Asliddin Komilov
le 22 Déc 2023
Catégories
En savoir plus sur Image Arithmetic dans Centre d'aide et File Exchange
Community Treasure Hunt
Find the treasures in MATLAB Central and discover how the community can help you!
Start Hunting!
