Figure changes during export
27 vues (au cours des 30 derniers jours)
Afficher commentaires plus anciens
Nathan Hogaboom
le 6 Août 2024 à 17:54
Commenté : Nathan Hogaboom
le 7 Août 2024 à 16:32
Hello everyone. I have created a loop where my function would save a plot of a series of posterior tangents overlaying vertebrae of the cervical spine. The problem is, after my function runs (code displayed below) only 5 out of the 6 lines appear on the plot. If I run it in isolation in the command window, all 6 lines appear. I have attached the images, the plot pre export with all 6 lines (ran in command window) and post export with the incorrect number (run as a function). I have gone through a number of times and cannot figure out why one line disappears when exporting. Any ideas?
Thanks in advance.
PS I have commented out parts of the code that are not relevant for this question. I did not delete so you were not confused about the input/output variables of my function.
function [c1_c7_angle,c2_c7_angle,c2c3_tangent,c3c4_tangent,c4c5_tangent,c5c6_tangent,c6c7_tangent]=rotation_angles(c1x,c1y,c2x,c2y,c3x,c3y,c4x,c4y,c5x,c5y,c6x,c6y,c7x,c7y,new_filename,i2)
%define posterior corners.
c2post=[c2x(1) c2y(1); c2x(4) c2y(4)];
c3post=[c3x(1) c3y(1); c3x(4) c3y(4)];
c4post=[c4x(1) c4y(1); c4x(4) c4y(4)];
c5post=[c5x(1) c5y(1); c5x(4) c5y(4)];
c6post=[c6x(1) c6y(1); c6x(4) c6y(4)];
c7post=[c7x(1) c7y(1); c7x(4) c7y(4)];
%c2_angle=rad2deg(atan((c2post(2,2)-c2post(1,2))/(c2post(2,1)-c2post(1,1))));
%c3_angle=rad2deg(atan((c3post(2,2)-c3post(1,2))/(c3post(2,1)-c3post(1,1))));
%c4_angle=rad2deg(atan((c4post(2,2)-c4post(1,2))/(c4post(2,1)-c4post(1,1))));
%c5_angle=rad2deg(atan((c5post(2,2)-c5post(1,2))/(c5post(2,1)-c5post(1,1))));
%c6_angle=rad2deg(atan((c6post(2,2)-c6post(1,2))/(c6post(2,1)-c6post(1,1))));
%c7_angle=rad2deg(atan((c7post(2,2)-c7post(1,2))/(c7post(2,1)-c7post(1,1))));
%c2c3_tangent=c2_angle-c3_angle;
%c3c4_tangent=c3_angle-c4_angle;
%c4c5_tangent=c4_angle-c5_angle;
%c5c6_tangent=c5_angle-c6_angle;
%c6c7_tangent=c6_angle-c7_angle;
%calculate c21-c7 angle by defining angle of inferior vertebral points.
%c1_angle=rad2deg(atan((c1y(1)-c1y(2))/(c1x(2)-c1x(1))));
%c2_inf_ang=rad2deg(atan((c2y(3)-c2y(4))/(c2x(3)-c2x(4))));
%c7_inf_ang=rad2deg(atan((c7y(3)-c7y(4))/(c7x(3)-c7x(4))));
%c1_c7_angle=c7_inf_ang-c1_angle;
%c2_c7_angle=c7_inf_ang-c2_inf_ang;
vertebra_matrix=[c2post;c3post;c4post;c5post;c6post;c7post];
post_x=[c2x(1) c2x(4) c3x(1) c3x(4) c4x(1) c4x(4) c5x(1) c5x(4) c6x(1) c6x(4) c7x(1) c7x(4)];
post_y=[c2y(1) c2y(4) c3y(1) c3y(4) c4y(1) c4y(4) c5y(1) c5y(4) c6y(1) c6y(4) c7y(1) c7y(4)];
theta=zeros([1 6]);
x_diff=zeros([1 6]);
y_diff=zeros([1 6]);
V=zeros([6 2]);
factor_distance=2;
imshow(i2,'InitialMagnification',100);
hold on;
for h=1:6
f=h*2;
d=f-1;
x_diff(h)=post_x(d)-post_x(f);
y_diff(h)=post_y(f)-post_y(d);
theta(h)=rad2deg(atan(y_diff/x_diff));
V(h,:)=vertebra_matrix(d,:)-vertebra_matrix(f,:);
pext(h,:)=vertebra_matrix(h,:)+V(h,:)*factor_distance;
ax=gca;
output_filename=sprintf('%s_rotation.tif',new_filename);
exportgraphics(ax,output_filename);
plot([post_x(f),pext(h,1)],[post_y(f),pext(h,2)],'r-')
end
end
0 commentaires
Réponse acceptée
dpb
le 6 Août 2024 à 18:36
Déplacé(e) : dpb
le 6 Août 2024 à 18:36
exportgraphics(ax,output_filename);
plot([post_x(f),pext(h,1)],[post_y(f),pext(h,2)],'r-')
The exportgraphics call is before the call to plot() so the last one hasn't yet been plotted...when the loop finishes at the command line, then the line shows on the image--but that last image isn't exported.
Reverse the order of those two lines and joy should/will ensue...
4 commentaires
dpb
le 6 Août 2024 à 21:11
Modifié(e) : dpb
le 7 Août 2024 à 16:28
OBTW, it would be more efficient to move the line
exportgraphics(ax,output_filename);
outside after the loop; no sense in rewriting the same file six times...one piece at a time; the final plot is the only one you're really interested in.
Plus de réponses (0)
Voir également
Catégories
En savoir plus sur Annotations dans Help Center et File Exchange
Community Treasure Hunt
Find the treasures in MATLAB Central and discover how the community can help you!
Start Hunting!