Why my Simulink does not work on RAPID ACCELERATOR mode?

Dear Ms,

I am experiencing an odd issue in my PC with the Simulink, I have not ever experienced this sort of problem that block me the posibility of runs my models on Rapid Accelerator mode (RAm). It always gives me an error, even with the MATLAB EXAMPLES, that is why I have concluded that it is not a problem of my own model, because they can runs in RAm in whatever other PCs. Finally, I have to highlight that have not occur in past versions of MATLAB. I have installed the release 2018b.

Anyone of you could please help me to solve it?, I would be very grateful if you help me to solve it.

[Walter Roberson]

please post a copy of the error

[Tony Castillo]

Simulation 2 2 Clear

06:44 PM Elapsed: 55 sec

Code Generation 1 1

Elapsed: 41 sec

### Building the rapid accelerator target for model: k1_3

"C:\PROGRA~3\MATLAB\SUPPOR~1\R2018b\3P.instrset\mingw_w64.instrset\bin/gcc" -c -pedantic -Wno-long-long -fwrapv -m64 -O0 -DCLASSIC_INTERFACE=1 -DALLOCATIONFCN=0 -DEXT_MODE=1 -DONESTEPFCN=0 -DTERMFCN=1 -DMULTI_INSTANCE_CODE=0 -DINTEGER_CODE=0 -DTID01EQ=0 -DTGTCONN -DON_TARGET_WAIT_FOR_START=0 -DMODEL=k1_3 -DNUMST=3 -DNCSTATES=22 -DHAVESTDIO -DNRT -DRSIM_PARAMETER_LOADING -DRSIM_WITH_SL_SOLVER -DENABLE_SLEXEC_SSBRIDGE=1 -DMODEL_HAS_DYNAMICALLY_LOADED_SFCNS=0 -IC:/Users/Tony C/DOCUME~1/MATLAB/MODELO_NUEVO_SESDE++/k1_ -IC:/Users/Tony C/DOCUME~1/MATLAB/MODELO_NUEVO_SESDE++/k1_/slprj/raccel/k1_3 -IC:/PROGRA~1/MATLAB/R2018b/extern/include -IC:/PROGRA~1/MATLAB/R2018b/simulink/include -IC:/PROGRA~1/MATLAB/R2018b/rtw/c/src -IC:/PROGRA~1/MATLAB/R2018b/rtw/c/src/rapid -IC:/PROGRA~1/MATLAB/R2018b/rtw/c/raccel -IC:/PROGRA~1/MATLAB/R2018b/rtw/c/src/ext_mode/common -IC:/PROGRA~1/MATLAB/R2018b/rtw/c/src/rtiostream/rtiostreamtcpip -IC:/PROGRA~1/MATLAB/R2018b/toolbox/coder/rtiostream/src/utils -IC:/PROGRA~1/MATLAB/R2018b/toolbox/physmod/powersys/facts/facts -IC:/PROGRA~1/MATLAB/R2018b/toolbox/physmod/powersys/DR/DR @k1_3_comp.rsp -o "rt_matrx.obj" "C:/PROGRA~1/MATLAB/R2018b/rtw/c/src/rt_matrx.c"

gcc: error: C/DOCUME~1/MATLAB/MODELO_NUEVO_SESDE++/k1_: No such file or directory

gcc: error: C/DOCUME~1/MATLAB/MODELO_NUEVO_SESDE++/k1_/slprj/raccel/k1_3: No such file or directory

gmake: *** [rt_matrx.obj] Error 1

The make command returned an error of 2

"An_error_occurred_during_the_call_to_make" no se reconoce como un comando interno o externo,

programa o archivo por lotes ejecutable.

### Build procedure for model: 'k1_3' aborted due to an error.

Unable to build a standalone executable to simulate the model 'k1_3' in rapid accelerator mode.

Caused by:

Error(s) encountered while building "k1_3":

### Failed to generate all binary outputs.

Component:Simulink | Category:Model error

Answer 1

[Walter Roberson]

Your files are under a directory that have a space in the name, TONY C

You could make attempts at fixing the tools so that they do not fail with spaces but by far the easier workaround is to use a location with no spaces in the directory name.

[Tony Castillo]

But how is it possible that in ACCELERATOR mode it works properly?. On the other side tryindg to do what you have already told me I receive the error message in the attached document, how can I solve it?

[Walter Roberson]

There are three levels of acceleration: Off; hosted (some code is generated but relies on Simulink being present ); and full code generation. The tools for full code generation are different than the tools for partial code generation .

You will probably have to exit matlab to rename the directory .

[Tony Castillo]

Thank you for your answer, your thoughts have helped me for solving my issues.

[Krasimir Terziev]

Thank you, that helped me alot.

The problem with me was that I had named my folder in Cyrillic.