Daniel Gelman
University of Western Ontario - Robarts Research Institute
Followers: 0 Following: 0
Statistiques
RANG
6 503
of 300 392
RÉPUTATION
7
CONTRIBUTIONS
13 Questions
1 Réponse
ACCEPTATION DE VOS RÉPONSES
0.0%
VOTES REÇUS
7
RANG
of 20 933
RÉPUTATION
N/A
CLASSEMENT MOYEN
0.00
CONTRIBUTIONS
0 Fichier
TÉLÉCHARGEMENTS
0
ALL TIME TÉLÉCHARGEMENTS
0
RANG
of 168 335
CONTRIBUTIONS
0 Problèmes
0 Solutions
SCORE
0
NOMBRE DE BADGES
0
CONTRIBUTIONS
0 Publications
CONTRIBUTIONS
0 Public Chaîne
CLASSEMENT MOYEN
CONTRIBUTIONS
0 Point fort
NOMBRE MOYEN DE LIKES
Feeds
Question
XCP master internal error, serial receive, Arduino external mode
I have a very simple model I am trying to deploy onto an Arduino Due target hardware in external mode (Monitor & Tune). Just try...
plus de 4 ans il y a | 1 réponse | 0
1
réponseQuestion
Running Simulink PID model with external reset and output saturation on Arduino target hardware.
On an Arduino, I've implemented an s-function to receive variables from a 2nd microcontroller via Serial. The model, which can...
environ 5 ans il y a | 1 réponse | 0
0
réponseQuestion
Simulink & Arduino: Transmit Serial strings
I am trying to transmit serial data out of an Arduino in Simulink, see model below. I am getting prompted with The 'MATLABS...
environ 5 ans il y a | 1 réponse | 1
1
réponseQuestion
Simulink/Arduino: serial receive byte stream
Hello, I am using Simulink to receive serial data via Arduino, which is receiving three bytes (unit8) of data from a 2nd microc...
environ 5 ans il y a | 1 réponse | 0
1
réponseQuestion
Simulink, Arduino as slave-receiver in I2C
I have 2 Arduinos: One Arduino MEGA is master-writer in an I2C bus, providing data at ~20 Hz. The other is an Arduino DUE in a...
environ 5 ans il y a | 1 réponse | 0
1
réponseQuestion
Could not connect to XCP slave: XCP Master internal error: Busy(0) or no timeout(2) for 255
Hello, I've used the S-Function Builder to use an Arduino library in Simulink. Specifically, I am trying to use the AccelSteppe...
plus de 5 ans il y a | 4 réponses | 6
4
réponsesQuestion
Sorted Execution Order, Initial Conditions, PID
Below is a closed-loop system of plant Gp(z) with unity gain. I also enabled to display the sorted execution order. <</matlab...
environ 8 ans il y a | 1 réponse | 0
1
réponseQuestion
Shaping PID to achieve load disturbance performance
I am using the PID Tuner for the PID Controller Block in Simulink. I am particularly interested in the output disturbance BODE p...
environ 8 ans il y a | 1 réponse | 0
1
réponseQuestion
ss2tf() Acting Oddly
I am constructing a few transfer functions and I believe this the output is very wrong. I am not expecting the numerator and den...
environ 9 ans il y a | 1 réponse | 0
1
réponseIdentical models in MATLAB and Simulink do not match each other
[Answered] Always be aware of significant figures. Even 0.0001 can make a difference in differential equations.
environ 9 ans il y a | 0
Question
How to Initialize a Discrete-Time Model?
Hello, I have the following discrete-time model. num = [0.02884 -0.02844]; den = [1 -1.7298 0.7337]; H = tf(num,...
environ 9 ans il y a | 1 réponse | 0
1
réponseQuestion
Identical models in MATLAB and Simulink do not match each other
I am noticing that discrete-time models I am using in Simulink do not match the same response in the Matlab environment. For ...
environ 9 ans il y a | 1 réponse | 0
1
réponseQuestion
New to FFT - is my result valid?
Hello, I am revisiting Matlab FFT after years of not practicing. I have a signal in which I removed the DC component and plot...
plus de 11 ans il y a | 1 réponse | 0
1
réponseQuestion
Raspberry Pi Simulink Communication Error
Hello, I am fairly new to Simulink and I am trying to incorporate a stand alone application running the model on a Raspberry ...
plus de 12 ans il y a | 1 réponse | 0
