Daniel Gelman

University of Western Ontario - Robarts Research Institute

Last seen: 7 mois il y a | Actif depuis 2013

Followers: 0 Following: 0

Message

MESc Biomedical Engineering student at Robarts Research Institute. Professional Interests: Image-Guided Interventions

Statistiques

Feeds

Question

XCP master internal error, serial receive, Arduino external mode
I have a very simple model I am trying to deploy onto an Arduino Due target hardware in external mode (Monitor & Tune). Just try...

plus de 3 ans il y a | 1 réponse | 0

1

réponse

Question

Running Simulink PID model with external reset and output saturation on Arduino target hardware.
On an Arduino, I've implemented an s-function to receive variables from a 2nd microcontroller via Serial. The model, which can...

environ 4 ans il y a | 1 réponse | 0

0

réponse

Question

Simulink & Arduino: Transmit Serial strings
I am trying to transmit serial data out of an Arduino in Simulink, see model below. I am getting prompted with The 'MATLABS...

plus de 4 ans il y a | 1 réponse | 1

1

réponse

Question

Simulink/Arduino: serial receive byte stream
Hello, I am using Simulink to receive serial data via Arduino, which is receiving three bytes (unit8) of data from a 2nd microc...

plus de 4 ans il y a | 1 réponse | 0

1

réponse

Question

Simulink, Arduino as slave-receiver in I2C
I have 2 Arduinos: One Arduino MEGA is master-writer in an I2C bus, providing data at ~20 Hz. The other is an Arduino DUE in a...

plus de 4 ans il y a | 1 réponse | 0

1

réponse

Question

Could not connect to XCP slave: XCP Master internal error: Busy(0) or no timeout(2) for 255
Hello, I've used the S-Function Builder to use an Arduino library in Simulink. Specifically, I am trying to use the AccelSteppe...

plus de 4 ans il y a | 4 réponses | 6

4

réponses

Question

Sorted Execution Order, Initial Conditions, PID
Below is a closed-loop system of plant Gp(z) with unity gain. I also enabled to display the sorted execution order. <</matlab...

plus de 7 ans il y a | 1 réponse | 0

1

réponse

Question

Shaping PID to achieve load disturbance performance
I am using the PID Tuner for the PID Controller Block in Simulink. I am particularly interested in the output disturbance BODE p...

plus de 7 ans il y a | 1 réponse | 0

1

réponse

Question

ss2tf() Acting Oddly
I am constructing a few transfer functions and I believe this the output is very wrong. I am not expecting the numerator and den...

plus de 8 ans il y a | 1 réponse | 0

1

réponse

Réponse apportée
Identical models in MATLAB and Simulink do not match each other
[Answered] Always be aware of significant figures. Even 0.0001 can make a difference in differential equations.

plus de 8 ans il y a | 0

Question

How to Initialize a Discrete-Time Model?
Hello, I have the following discrete-time model. num = [0.02884 -0.02844]; den = [1 -1.7298 0.7337]; H = tf(num,...

plus de 8 ans il y a | 1 réponse | 0

1

réponse

Question

Identical models in MATLAB and Simulink do not match each other
I am noticing that discrete-time models I am using in Simulink do not match the same response in the Matlab environment. For ...

plus de 8 ans il y a | 1 réponse | 0

1

réponse

Question

New to FFT - is my result valid?
Hello, I am revisiting Matlab FFT after years of not practicing. I have a signal in which I removed the DC component and plot...

plus de 10 ans il y a | 1 réponse | 0

1

réponse

Question

Raspberry Pi Simulink Communication Error
Hello, I am fairly new to Simulink and I am trying to incorporate a stand alone application running the model on a Raspberry ...

plus de 11 ans il y a | 1 réponse | 0

1

réponse