lsm6dsl

Connect LSM6DSL sensor on Raspberry Pi hardware I2C bus

Since R2021a

Description

The lsm6dsl object reads ambient temperature, and linear acceleration and angular velocity along the X, Y, and Z axes using the STMicroelectronics^® I2C-based LSM6DSL inertial measurement unit (IMU) sensor interfaced with the Raspberry Pi^® hardware. Before you use the lsm6dsl object, ensure that the I2C interface is enabled on your Raspberry Pi kernel. You can then create a connection to the Raspberry Pi board using the raspi object and set its properties. For more information, see raspi.

Creation

Syntax

sensor = lsm6dsl(mypi)

sensor = lsm6dsl(mypi,Name,Value)

Description

sensor = lsm6dsl(mypi) creates a LSM6DSL sensor object with default property values. The object represents a connection to the sensor on the Raspberry Pi hardware mypi.

sensor = lsm6dsl(mypi,Name,Value) creates a LSM6DSL sensor object with properties using one or more Name,Value arguments.

Input Arguments

mypi — Raspberry Pi hardware connection

raspi object

Raspberry Pi hardware board connection specified as a raspi object.

Example: sensor = lsm6ds1(mypi) creates a connection to the LSM6DSL sensor on the Raspberry Pi object mypi.

Name-Value Arguments

Specify optional pairs of arguments as Name1=Value1,...,NameN=ValueN, where Name is the argument name and Value is the corresponding value. Name-value arguments must appear after other arguments, but the order of the pairs does not matter.

Before R2021a, use commas to separate each name and value, and enclose Name in quotes.

Bus — I2C bus address of Raspberry Pi board

'i2c-0' | 'i2c-1'

I2C bus address of the Raspberry Pi hardware board.

Example: sensor = lsm6dsl(mypi, 'Bus', 'i2c-1') creates the sensor object on the 'i2c-1' bus of the Raspberry Pi board.

Data Types: char

I2CAddress — Specify I2C address of sensor

0x6A | 0x6B

Specify the I2C address of the sensors when multiple I2C devices with the expected address for LSM6DSL are connected to the same hardware board. LSM6DSL can have two I2C addresses depending on the logic level on pin SDO/SA0 of the sensor.

Pin Name	Pin State	I2C Address
SDO/SA0	Low	0x6A
	High	0x6B

You can specify the I2C address in:

• Hexadecimal, decimal, or binary format

• String of hexadecimal value of I2C Address

• Character vector of hexadecimal value of I2C Address

Example: imu = lsm6dsl(mypi,'I2CAddress',0x6A)

0x6A is the I2C address of the accelerometer and gyroscope of LSM6DSL connected to Raspberry Pi board.

If not specified, the object will be created with one of the available I2C device address in the table. Availability of I2C device with the expected address will be determined by using scanI2CBus.

Object Functions

readAcceleration	Read one sample of acceleration from sensor
readAngularVelocity	Read one sample of angular velocity from sensor
readTemperature	Read one sample of temperature from sensor

Examples

Create LSM6DSL Sensor Connection

Ensure that the I2C interface on the Raspberry Pi kernel is enabled and then create an lsm6dsl sensor object.

You can enable the I2C interface using:

• Raspberry Pi Kernel I2C Interfacing options on Linux terminal. For more information, see Enable I2C Interface on Raspberry Pi Hardware Kernel or

• Raspberry Pi Resource Monitor App. For more information, see Enabling External Peripherals on Raspberry Pi Hardware Kernel.

Create a connection from MATLAB^® to the Raspberry Pi hardware board.

mypi = raspi('raspberrypi-hysdu8X38o','rocky','bullwinkle')

mypi = 

  Raspi with Properties:

           DeviceAddress: 'raspberrypi-hysdu8X38o'
                    Port: 18734
               BoardName: 'Raspberry Pi 3 Model B+'
           AvailableLEDs: {'led0'}
    AvailableDigitalPins: [4,5,6,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27]
    AvailableSPIChannels: {‘CE0’,’CE1’}
       AvailableI2CBuses: {'i2c-1'}
             I2CBusSpeed: 100000
        AvailabelWebCams: mmal service 16.1 (platform:bcm2835-v4l2)

Get the addresses of the LSM6DSL sensor connected to the I2C bus 'i2c-1'.

sensor = scanI2CBus(mypi,'i2c-1');

ans =
 

  1×1 cell array
 

    {'0x6B'}

Create an lsm6dsl sensor object on the I2C bus 'i2c-1' on address '0x6B'.

sensor = lsm6dsl(mypi,'Bus','i2c-1','I2CAddress','0x6B');

sensor = 

  lsm6dsl with properties:

                         I2CAddress: 107 ("0x6B")
                                Bus: i2c-1

Extended Capabilities

C/C++ Code Generation

Generate C and C++ code using MATLAB® Coder™.

• Timestamp value is always returned in seconds.

• When you create an lsm6dsl sensor object and do not specify the I2C address in the name-value pair, the default I2C address is considered by the LSM6DSL sensor. For the LSM6DSL sensor, the default I2C address is '0x6A'.

Version History

Introduced in R2021a