ALBERT ALEXANDER STONIER
NORTH EASTERN UNIVERSITY, BOSTON, USA
Followers: 0 Following: 0
Dr.S.ALBERT ALEXANDER is the post doctoral research fellow in North eastern University, Boston, USA. He completed his Ph.D. in the performance improvement of solar Photovoltaics under Anna University, India. He completed his master degree in Power Electronics and Drives with Anna University rank. As a principal investigator he has completed three major research projects sponsored by Government of India. For detailed profile visit www.ootyalex.webs.com
Statistiques
RANG
359
of 289 969
RÉPUTATION
220
CONTRIBUTIONS
0 Questions
23 Réponses
ACCEPTATION DE VOS RÉPONSES
0.00%
VOTES REÇUS
88
RANG
3 178 of 19 612
RÉPUTATION
488
CLASSEMENT MOYEN
4.60
CONTRIBUTIONS
2 Fichiers
TÉLÉCHARGEMENTS
13
ALL TIME TÉLÉCHARGEMENTS
3388
CONTRIBUTIONS
0 Publications
CONTRIBUTIONS
0 Public Chaîne
CLASSEMENT MOYEN
CONTRIBUTIONS
0 Point fort
NOMBRE MOYEN DE LIKES
Feeds
Tuning a PID Controller in Simpowersystem Model
Either to derive the model and can obtain the gain values. Orelse, its by trial and error.
plus de 2 ans il y a | 0
How i can i design hollow square wave inverter?
The switching frequency of 12kHz can be decided by the frequency of the triangle waveform. You can use saw tooth block and then ...
plus de 2 ans il y a | 0
| A accepté
How to speed up my Simulink model?
Change the solver type and check for the speed
plus de 7 ans il y a | 1
| A accepté
how to plot iv curve for solar pv
In MATLAB 2016 you have this option to plot both PV and IV characteristics simultaneously.
plus de 7 ans il y a | 0
incremental conductance MPP method
You can set the initial value as any value between 0 to 1. Normally we can set as 0.4. Based on the variations in the input sola...
plus de 7 ans il y a | 0
Problem related to powergui block
It is only because of the dimensions which you have specified for the signal. Kindly change the dimensions and proceed with.
plus de 7 ans il y a | 0
simulink for three phase 120 degree inverter
If your load requirement is 50GW, kindly consider that you using single source (fuel cell) or with multiple sources like (solar,...
plus de 7 ans il y a | 0
Hi, Could I get help for coding or designing SVPWM for single phase 3 level inverter?
You can find the SVPWM generator block in MATLAB 2016B.
plus de 7 ans il y a | 0
how to give values in pulse generator for simulation of cascaded hybrid 5 level inverter in matlab simulink ?
You can make use of multilevel PWM generator which is available in MATLAB/Simulink 2016b.
plus de 7 ans il y a | 0
Is there a PWM block available in Simulink?
There are so many options for the generation of PWM in MATLAB. Some are listed as below: 1. You can use a function generator an...
plus de 7 ans il y a | 1
| A accepté
How to calculate Total harmonic distortion using FFT analysis tool of power gui block
The normal cycle which need to be considered for the FFT analysis is 20 as much dealt in various IEEE literature. In order to re...
plus de 7 ans il y a | 7
How i can set target data for desired output in Neural network app in MATLAB?
If you declared the targets earlier while creating the network type, this error will not be shown
plus de 7 ans il y a | 0
How long is Simulink trial period
It will be available for a month period.
plus de 7 ans il y a | 0
| A accepté
I need automatic switch,but once it is turn ON and it should not be turn OFF
You can try with the file given in the link: https://www.mathworks.com/matlabcentral/fileexchange/59461-function-based-on-off-co...
plus de 7 ans il y a | 0
how can I connect the solar cell block from sim electronics to block from sim power system library?
You cannot connect the simscape directly to the simpower systems. You need to use the simscape to simpower converter to get the ...
plus de 7 ans il y a | 1
How to generate a switch fault in Mosfet/IGBT?
You can open the switch for considering the open switch fault and connect both the legs for a short circuit fault.
plus de 7 ans il y a | 12
How do I implement a Zener diode in Simulink?
You can change the properties of a ordinary diode with respect to the barrier voltage level to get the zener diode.
plus de 7 ans il y a | 12
How the level shift of carrier in PWM inverter can be done in power electronics simulation in matlab
You need to generate 4 carrier signals in which 2 are above the zero reference and 2 are below the zero reference for a single ...
plus de 7 ans il y a | 11
What is data in regression plot in neural network?
The circled shaped in the input data which you have used for the training of neural network.
plus de 7 ans il y a | 11
Error while running Simulink model in MATLAB 2015b?
May I know the process or application which you are dealing with. Also consider that the updated version has the licence pair of...
plus de 7 ans il y a | 11
Generating characteristics of power electronics devices
You can make use of mathematical models for the extraction of characteristics as similar to that of a solar cell in MATLAB
plus de 7 ans il y a | 0
How to solve the optimization problem as follows
You can include this function as the objective functions and the related constraints as being real numbers. You can use either G...
plus de 7 ans il y a | 10
| A accepté