Community Profile

photo

Akshay Khadse

MathWorks

Last seen: plus d'un an il y a Actif depuis 2018

I am a part of Engineering Development Group at MathWorks. I have an Electrical Engineering background with specialization in Control Systems.

All the comments made here are solely my opinions and MathWorks is not liable for any of these. I am committed to helping this community to the best of my abilities. However, it is perfectly fine for other members to correct me in pursuit of forum enrichment.

Statistiques

  • Knowledgeable Level 3
  • Knowledgeable Level 2
  • First Answer

Afficher les badges

Content Feed

Afficher par

A répondu
Auto Simulation with Simulink
If not than you could use the sim command in a MATLAB script, log the signals in your model and save the output from this script...

presque 5 ans il y a | 0

A répondu
Open SimulinkProject along with model
I am ssuming that you are using open_system command to open the model file. However, this command cannot open the Simulink Proj...

environ 5 ans il y a | 0

A répondu
Simulink model developped and running well in 2017b, exceed Jacobian elements allowed in memory in 2018b
This happens when the solver is kept as 'auto'. Using auto solver will fail to select the right solver if the number of jacobia...

environ 5 ans il y a | 0

A répondu
Not able to connect zynq7010 to MATLAB
Please try to reset everything before connecting: Delete everything on the SD card Get the correct IP address of the hardware ...

environ 5 ans il y a | 0

A répondu
Simulink Real-Time with RS-232 (receiving data)
Please run the following command in the MATLAB Command Window to verify the Simulink Real Time installation for R2020a and earli...

environ 5 ans il y a | 0

| A accepté

A répondu
Speed control with DC Motor w/ Encoders PID Control L298N Driver
Hi Dalton, As per my knowledge, this motor contains a two channel quadrature encoder which has four connectors and the remainin...

environ 5 ans il y a | 0

A répondu
How do I pass Sensor Data to a GUI?
You could directly set the Value property of the Gauge in a MATLAB App. In my opinion, this is the simplest way to pass the data...

environ 5 ans il y a | 0

A répondu
which is more accurate , Battery modeling (table based ) approach of simscape or Equivalent circuit model approach of simscape electronics?
Both the approaches are accurate. It really depends on the availability of the information about the battery. Case 1: If you h...

environ 5 ans il y a | 0

| A accepté

A répondu
How to name a physical signal in simscape
This is currently not supported. Our teams are already aware of this.

environ 5 ans il y a | 0

| A accepté

A répondu
How to create a SIMULINK model standalone application for those whose does not have Simulink
Standalone deployment of only the MATLAB apps is presently supported.

environ 5 ans il y a | 0

| A accepté

A répondu
How to set initial condition y(1)=1 in solving ODE using Simulink?
As Aquatris mentioned, the Start Time for simulation should be specified as 1 from the Configuration Parameters. Then, you ca...

environ 5 ans il y a | 1

A répondu
How to read in big parts of text to my code
This could easliy be done by writing a function to use dialog with an edit uicontrol in MATLAB based on the following example:ht...

environ 5 ans il y a | 0

A répondu
Options of pcolor lines
As per my knowledge, it not possible to selectively hide the grid in this case. Following are the two alternatives: 1) Hide the...

environ 5 ans il y a | 0

A répondu
How can I represent losses in pipes?
As per my knowledge, equivalent length is given by . Here, the and f are dimensionless and unit of is meters. Hence, the unit...

environ 5 ans il y a | 0

A répondu
Add text/ annotation to table in figure window
As per my knowledge, text requires an axis as a parent. If its not present, an axis object will automatically get created. In...

environ 5 ans il y a | 1

| A accepté

A répondu
how to plot each raw and each column of the matrix?
Assuming that you are facing difficulty in superimposing graphs, you could try any of the following suggestions: 1) Remove the ...

environ 5 ans il y a | 0

A répondu
RTX 2080 GPU coder, what to do?
You could try the following steps to diagnose the cause for this error: 1) Check if you can execute the following command in th...

environ 5 ans il y a | 0

A répondu
how to install the SPM 12 into Matlab?
I found the installation instructions on the following SPM Wiki Page: https://en.wikibooks.org/wiki/SPM/Installation_on_Windows...

plus de 5 ans il y a | 2

A répondu
hOW TO READ AN IMAGE INTO MATLAB STORED AS PDF
As per my knowledge, extracting images from PDF using MATLAB alone is not possible due to the varying methods to store data in t...

plus de 5 ans il y a | 0

A répondu
How can I plot multiple waveforms in a single plot without using sub plot function ? I have attached an image for reference.
You could plot multiple waveforms on the same graph by using the hold command. Please refer the following example for correct u...

plus de 5 ans il y a | 0

A répondu
Just installed Matlab R2018b on Ubuntu. If I type a subject in "help", get the text below, no images. Started matlab with - softwareopengl. ?Is this a graphics issue or some other setting?
As per my knowledge this issue is caused due to some missing shared libraries required for proper functioning of the jxbrowser. ...

plus de 5 ans il y a | 2

A répondu
Why can't I access Toolbox functions
The drawcircle and drawrectangle were introduced in MATLAB R2018b. Usually, this information can be found at the bottom most par...

plus de 5 ans il y a | 0

| A accepté

A répondu
App developer: How to clean or reset a table
I am assuming that you have a UITable in your app created via MATLAB App Designer. There is no direct command to clear the co...

plus de 5 ans il y a | 3

A répondu
How to save 12 bit PNG images
MATLAB scales the image intensity values from 12-bit to 16-bit after it loads a 12-bit image via the following algorithm: % W c...

plus de 5 ans il y a | 0

| A accepté

A répondu
Simulink Nonlinear Inductor Configuration
The plots shown under the section 'Simulation Results from Simscape Logging' have been generated by plotting the Simscape logged...

plus de 5 ans il y a | 0

A répondu
hgexport: undefined function handle
I am assuming that you have a .fig file saved from MATLAB R2015a which you are trying to open and save to .eps using 'hgexport' ...

plus de 5 ans il y a | 0

A répondu
Matlab and Ubuntu fresh installations: buttons (log in, Add-Ons) do not work
This error usually occurs when there are incompatible libraries. As you mentioned, 'libatk-1.0.so.0' is causing this issue on...

plus de 5 ans il y a | 0

| A accepté

A répondu
Is there a way to embed a colorbar in a webmap, or am I going about this the wrong way?
As per my knowledge, 'webmap' opens a new browser window whereas 'colormap' cannot plot in the browser. Therefore, you are getti...

plus de 5 ans il y a | 0

A répondu
How do I actuate a radio button in a button group programmatically.
Can you post your code here? I would suggest you to refer the documentation for ' <https://www.mathworks.com/help/matlab/ref/...

plus de 5 ans il y a | 0

A répondu
How to increase contrast of a 3d plot? Should I set colorbar to log scale?
Instead of modifying the colormap scale, you could take a log of the ColorMapData values to magnify your data variations. I t...

plus de 5 ans il y a | 0

| A accepté

Charger plus