Specify Signal Ranges
Simulink® blocks allow you to specify a range of valid values for their output signals. Specifying signal ranges help you to optimize data types and improve generated code.
If you have Embedded Coder®, Simulink Coder™ can optimize the code that you generate from the model by taking into account the minimum and maximum values that you specify for signals and parameters. This optimization can remove algorithmic code and affect the results of some simulation modes such as SIL or external mode. For more information, see Optimize using the specified minimum and maximum values (Embedded Coder).
Blocks That Allow Signal Range Specification
The following blocks allow you to specify ranges for their output signals:
Work with Signal Ranges in Blocks
To specify signal ranges for most blocks, use the Output minimum and Output maximum parameters of a block to specify a range of valid values for the block output signal. Exceptions include the Data Store Memory, Inport, In Bus Element, Outport, Out Bus Element, and Signal Specification blocks, for which you use their Minimum and Maximum parameters to specify a signal range. See Blocks That Allow Signal Range Specification for a list of applicable blocks.
To access these parameters, use the Property Inspector (on the Modeling tab, under Design, click Property Inspector), the Model Data Editor (on the Modeling tab, click Model Data Editor), or the block dialog box.
Specify a minimum or maximum as an expression that evaluates to a scalar,
real number with
double data type. For example, you can
A literal number such as
98.884. Implicitly, the data type is
A numeric workspace variable (see Share and Reuse Block Parameter Values by Creating Variables) whose data type is
double. Use this technique to share a minimum or maximum value between multiple data items.
When you use a variable to set the
Maxproperty of a
Simulink.BusElementobject, the current value of the variable is assigned to the object. The
Maxproperties of the object are not affected by future changes to the variable.
The scalar value that you specify applies to each element of a composite signal (for example, when the signal is nonscalar or a bus). For information about scalar expansion, see Scalar Expansion of Inputs and Parameters.
To leave the minimum or maximum of a signal unspecified, use an empty matrix
, which is the default value.
Specify Ranges for Modeling Constructs
If you use modeling constructs such as buses, data stores, and Stateflow® charts, you can use different techniques to specify design range information. Use the information in the table.
|Description of Target Signal||Technique and More Information|
Numerically complex signal
When you specify an Output
minimum or Output
maximum for a signal that is
numerically complex, the specified minimum and
maximum values apply separately to the real part
and to the imaginary part of the complex number.
If the value of either part of the number is less
than the minimum, or greater than the maximum, the
complex number is outside the specified range. No
range checking occurs against any combination of
the real and imaginary parts, such as
Signal elements in a bus
If you assemble the bus by using a Bus Creator block, you can specify range information on the upstream blocks that feed the Bus Creator block.
Regardless of the technique you use to assemble the bus,
you can create a
Signal in a MATLAB Function block
Use the Symbols pane and Property Inspector to specify the Minimum and Maximum properties of the variables. See Set General Variable Properties.
Signal in a Stateflow chart
Set the Minimum and Maximum properties of the corresponding Stateflow data. See Limit range (Stateflow).
Signal that you associate with an
object (such as a
Data store (Data Store
Memory block or
For a Data Store
Memory block, set the
Maximum block parameters. For
a signal object, set the
Troubleshoot Signal Range Errors
Simulink provides a diagnostic named Simulation range checking, which you can enable to detect when signals exceed their specified ranges during simulation. When enabled, Simulink compares the signal values that a block outputs with both the specified range (see Work with Signal Ranges in Blocks) and the block data type. That is, Simulink performs the following check:
DataTypeMin ≤ MinValue ≤ VALUE ≤ MaxValue ≤ DataTypeMax
DataTypeMinis the minimum value representable by the block data type.
MinValueis the minimum value the block should output, specified by, e.g., Output minimum.
VALUEis the signal value that the block outputs.
MaxValueis the maximum value the block should output, specified by, e.g., Output maximum.
DataTypeMaxis the maximum value representable by the block data type.
It is possible to overspecify how a block handles signals that exceed particular ranges. For example, you can specify values (other than the default values) for both signal range parameters and enable the Saturate on integer overflow parameter. In this case, Simulink displays a warning message that advises you to disable the Saturate on integer overflow parameter.
Enable Simulation Range Checking
To enable the Simulation range checking diagnostic:
In your model window, on the Modeling tab, click Model Settings.
Simulink displays the Configuration Parameters dialog box.
In the Select tree on the left side of the Configuration Parameters dialog box, click the Diagnostics > Data Validity category. On the right side under Signals, set the Simulation range checking diagnostic to
Click OK to apply your changes and close the Configuration Parameters dialog box.
See Simulation range checking for more information.
Simulate Models with Simulation Range Checking
To check for signal range errors or warnings:
Enable the Simulation range checking diagnostic for your model (see Enable Simulation Range Checking).
In your model window, click Run to simulate the model.
Simulink simulates your model and performs signal range checking. If a signal exceeds its specified range when the Simulation range checking diagnostic specifies
error, Simulink stops the simulation and generates an error (for example, in the Diagnostic Viewer).
Otherwise, if a signal exceeds its specified range when the Simulation range checking diagnostic specifies
warning, Simulink generates a warning message in the MATLAB® Command Window. Each message identifies the block whose output signal exceeds its specified range, and the time step at which this violation occurs.
Signal Range Propagation for Virtual Blocks
Some virtual blocks (see Nonvirtual and Virtual Blocks) allow you to specify ranges for their output signals, for example, the Inport and Outport blocks. When the Simulation range checking diagnostic is enabled for a model that contains such blocks, the signal range of the virtual block propagates backward to the first instance of a nonvirtual block whose output signal it receives. If the nonvirtual block specifies different values for its own range, Simulink performs signal range checking with the tightest range possible. That is, Simulink checks the signal using the larger minimum value and the smaller maximum value.
For example, consider the following model:
In this model, the Constant block specifies its Output maximum parameter as 300, and that of the Inport block is set to 100. Suppose you enable the Simulation range checking diagnostic and simulate the model. The Inport block back propagates its maximum value to the nonvirtual block that precedes it, i.e., the Constant block. Simulink then uses the smaller of the two maximum values to check the signal that the Constant block outputs. Because the Constant block outputs a signal whose value (200) exceeds the tightest range, Simulink generates an error.
Unexpected Errors or Warnings for Data with Greater Precision or Range than
When a data item (signal or parameter) uses a data type other
double, before comparison, Simulink casts
the data item and each design limit (minimum or maximum value that
you specify) to the nondouble data type. This technique helps prevent
the generation of unnecessary, misleading errors and warnings.
However, Simulink stores design limits as
comparison. If the data type of the data item has higher precision
double (for example, a fixed-point data type
with a 128-bit word length and a 126-bit fraction length) or greater
exactly represent the value of a design limit, Simulink can generate
unexpected warnings and errors.
If the nondouble type has higher precision, consider rounding
the design limit to the next number furthest from zero that
represent. For example, suppose that a signal generates an error after
you set the maximum value to
At the command prompt, calculate the next number furthest from zero
double can represent.
format long 98.8847692348509014 + eps(98.8847692348509014)
ans = 98.884769234850921
Use the resulting number,
to replace the maximum value.